Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Dryer no heat
Options
Go to last post Go to first unread
Model: LG5761XSWO Brand: Whirlpool Age: More than 10 years
Previous Topic Next Topic
hawknic  
#1 Posted : Sunday, May 5, 2013 6:31:59 AM(UTC)
hawknic

Rank: Member

Groups: Registered
Joined: 5/1/2013(UTC)
Posts: 4
My gas dryer glows for 10 -15 seconds then it clicks and does not ignite.
It tries again in another minute. I can smell gas so I turn it off.
I replaced the coils and it does the same thing. Could it be the gas valve and I could I check the valve. There is no lint build up any where.
Thanks
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
ApplianceJunk  
#2 Posted : Sunday, May 5, 2013 7:45:08 AM(UTC)
ApplianceJunk

Rank: Advanced Member

Groups: Senior Expert
Joined: 7/24/2007(UTC)
Posts: 2,277
I would check the thermal fuse first.
Back to top
hawknic  
#3 Posted : Sunday, May 12, 2013 7:13:35 AM(UTC)
hawknic

Rank: Member

Groups: Registered
Joined: 5/1/2013(UTC)
Posts: 4
I checked the thermal fuse. What would be the next step? Could the gas valve bot be opening properly?
Back to top
hawknic  
#4 Posted : Sunday, May 12, 2013 8:59:08 AM(UTC)
hawknic

Rank: Member

Groups: Registered
Joined: 5/1/2013(UTC)
Posts: 4
Ok I replaced coils, ignitor is good ( 80 ohms) the flame sensor good. Dryer glows but no ignition. Any ideas? Thank you
ps looked at new dryers..ouch would like to repair old one.
Back to top
scott5495  
#5 Posted : Sunday, May 12, 2013 9:36:39 AM(UTC)
scott5495

Rank: Member

Groups: Registered
Joined: 4/19/2013(UTC)
Posts: 188
even though the ignitor checks good, it can still be bad. i have found that ignitors will read good until they begin to draw amperage. an ignitor can have a small crack in it and still glow. the ignitor must draw at least three amps to activate the coils to open the gas valve. one of the coils is a holding coil. did you replace both coils?
Back to top
hawknic  
#6 Posted : Thursday, May 16, 2013 4:04:05 AM(UTC)
hawknic

Rank: Member

Groups: Registered
Joined: 5/1/2013(UTC)
Posts: 4
Yes I replaced both coils. I am going to replace the ignitor. I was told that when they get into the 90 ohm reading to replace. I can smell gas so I don't think it's the valve. Thank you Scott5495 appreciate the reply it reinforces decision.
Back to top
Users browsing this topic
Guest (2)
Similar Topics
LG Gas Dryer No Heat - Control Panel? (Dryer Repair)
by TomDBBills 1/29/2022 4:03:42 PM(UTC)
Samsung Dryer no heat (Dryer Repair)
by Guest 10/5/2021 5:41:36 PM(UTC)
LG gas dryer no heat (Dryer Repair)
by Guest 8/15/2021 10:28:45 AM(UTC)
Kenmore model 11060022010 electric dryer no heat (Dryer Repair)
by mike5466 5/1/2020 10:29:22 AM(UTC)
Samsung dryer no heat - 5 possible components? (Dryer Repair)
by sgsiegel 2/11/2018 7:02:33 AM(UTC)
gas dryer no heat (Dryer Repair)
by tombeird 11/8/2017 2:32:42 PM(UTC)
Maytag Atlantic Dryer no heat but everything tests ok (Dryer Repair)
by oldebrowndog 11/10/2015 11:38:46 AM(UTC)
Dryer No Heat.mind boggling! (Dryer Repair)
by andrelaplume 10/10/2015 7:22:06 PM(UTC)
Dryer no heat (Dryer Repair)
by fhorta 9/28/2015 12:22:36 PM(UTC)
Whirlpool gas dryer no heat (Dryer Repair)
by alabamainnevada@yahoo.com 6/23/2015 5:54:15 PM(UTC)
hot point dryer no heat and timer doesn't advance (Dryer Repair)
by gooseofdeuce 4/18/2015 8:29:56 AM(UTC)
Dryer no heat (Dryer Repair)
by SEMIFAST0 3/15/2015 9:00:11 AM(UTC)
Gas Dryer NO HEAT/FLAME and possible bad timer? (Dryer Repair)
by noles9399 2/26/2015 10:12:14 PM(UTC)
roper dryer no heat (Dryer Repair)
by chuck vaughn 12/1/2014 1:35:50 PM(UTC)
maytag gas dryer no heat (Dryer Repair)
by steve5024 11/8/2014 8:57:28 AM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET