Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

5 Pages123>»
Options
Go to last post Go to first unread
demark  
#1 Posted : Monday, December 24, 2007 9:43:06 AM(UTC)
demark

Rank: Member

Groups: Registered
Joined: 12/24/2007(UTC)
Posts: 1

I have a Kenmore dishwasher that appears to go through its cleaning cycle however there is soap residue left in dispenser and dishes are not clean. "Clean" light flashes 7 times--does that refer to a trouble code?

Thanks-Merry Christmas !!
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
Gene  
#2 Posted : Monday, December 24, 2007 10:10:25 AM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
The "Clean" light, flashing 7 times means a problem in the heating circuit.

Reset the control as described in the tech's sheets (located in a pouch behind the bottom panel).

If it'll happen again, check the heating element and the high limit thermostat.

The model number you posted is incomplete.

Happy Holidays!

Gene.
richappy  
#3 Posted : Tuesday, December 25, 2007 12:51:04 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Your hot water may be too cold, just increase temperature.
Open door, within 3 seconds hit high temp. scrub,energy saver dry, then repeat (if no such buttons press similar ones} Close door and press cancel. Good luck,Merry Christmas.
Neal  
#4 Posted : Thursday, December 27, 2007 1:17:50 PM(UTC)
Neal

Rank: Member

Groups: Registered
Joined: 12/27/2007(UTC)
Posts: 21

I have the same problem with my Kenmore. How do you reset the dishwasher as stated in the early post. There's nothing in my tech sheet.
Thanks.
richappy  
#5 Posted : Thursday, December 27, 2007 1:47:43 PM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Just follow the directions for Demark above
Neal  
#6 Posted : Friday, December 28, 2007 1:52:02 AM(UTC)
Neal

Rank: Member

Groups: Registered
Joined: 12/27/2007(UTC)
Posts: 21

I was able to reset the flashing green light. There was no error code shown afterwards. Then I ran the normal wash cycle. Took a few minutes
to start. On the screen started at 55, went down to 48 (?) then dropped to 2. Finished out the cycle. Afterwards the flashing green light. I could do the sequence all over again. Neal
richappy  
#7 Posted : Friday, December 28, 2007 3:28:20 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Check your service sheet. The dishwasher is sensing a bad heater. Check the heater and heater thermostat.
Neal  
#8 Posted : Friday, December 28, 2007 3:53:02 AM(UTC)
Neal

Rank: Member

Groups: Registered
Joined: 12/27/2007(UTC)
Posts: 21

I'm at work right now, How do I check those items? I'll check them later this evning. Thanks for your help.
richappy  
#9 Posted : Friday, December 28, 2007 5:02:50 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Crunch your model # in this site to get assembly info.
Neal  
#10 Posted : Friday, December 28, 2007 4:05:21 PM(UTC)
Neal

Rank: Member

Groups: Registered
Joined: 12/27/2007(UTC)
Posts: 21

Richappy, Where on this site do you find that info? First time user, Sorry.
Thanks
Users browsing this topic
Guest (4)
5 Pages123>»
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.