Rank: Advanced Member
Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
|
Sorry, just replace the timer. That will almost certainly fix it, but if it doesn't and you purchased from this site you can return it, so no risk.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 12/4/2012(UTC)
Posts: 4
|
I have the same problem but I did replace the timer and it does the exact same thing. The washer in whole operates perfectly except it won't spin unless I open lid or shut timer off and turn back on. Any other suggestions other than the timer and lid switch?
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2012(UTC)
Posts: 5
|
I believe it is the lack of pause in the timer. Did you replace the timer with a NEW unit?
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 12/4/2012(UTC)
Posts: 4
|
yeah. I ordered from appliance pros, and it does pause before it goes into spin cycle. Its like the clutch is not releasing from some reason. but it pauses for 5 seconds or more after agitating. not sure what do do now...but i know im not buying a new one. ill just keep opening the lid.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 12/4/2012(UTC)
Posts: 4
|
you think theres any chance its the start motor capacitor???
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2012(UTC)
Posts: 5
|
Originally Posted by: chrisnelson1  you think theres any chance its the start motor capacitor??? No, because your motor would not turn at all if it was the start capacitor. It is the pause at that timed moment that causes it to spin after draining. My lid switch was acting up so I replaced it and I just leave the lid up until I am ready to drain and spin. I do not know what to tell you other than keep lifting the lid. I have been doing this for some time now and it is not as much of a bother as I thought it would be; it turns out my clothes get washed faster rather than me forgetting they are there and getting side tracked.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806
Was thanked: 7 time(s) in 7 post(s)
|
The pause directly after agitation has nothing to do with neutral drain. That pause is to allow the motor to stop before starting again in the opposite direction. Then it should drain without spin for a minute or two and then pause again. The second pause is to allow the neutral drain to release. Then it will start again spinning and draining. If the pause after drain does not release neutral drain then there's likely something wrong with the neutral drain mechanism in the gearcase. You can rule out the clutch by observing the clutch hub during drain and spin. You must remove the cabinet, bypass the lid switch and observe the clutch hub. During the initial drain period directly after agitate, the clutch hub does not rotate. After the motor pauses and starts again, the clutch hub should be rotating. If it is and the basket is not spinning, then the clutch is slipping. Eric 
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2012(UTC)
Posts: 5
|
Eric - thanks for that info. If the clutch hub is slipping why would an intensional pause (lifting the lid or pushing in and pulling out the start button) cause the unit to thump into the spin mode?
|
|
|
|
|
|
Rank: Advanced Member
Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806
Was thanked: 7 time(s) in 7 post(s)
|
I don't have an answer for that, but observing the clutch hub would certainly tell us where to look further.
Eric
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 3/6/2018(UTC)
Posts: 2
|
I'm not an appliance guy, but I dabble in troubleshooting...I'm not buying into the timer cure-all solution presented here. I mean, haven't clocks been around for a millennia or two? I want to assume humanity has mastered the clock by now.
In my case my washer was recently repaired for making a clunking sound during agitation...it was only AFTER the appliance guy worked on my unit that I started having issues with the spin not engaging. In addition, the unit makes a strange hum noise when it is supposed to be spinning but isn't. I have also observed what sounded like a shot of water being introduced during the spin cycle, which I honestly assumed should not be happening...this was the only potential symptom I observed that MAY be related to the timer. Even then that could be normal, and I still wouldn't suspect the timer hardware if it were abnormal.... I'd suspect the numb-nuts who botched the repair that caused this issue. Perhaps the timer can be calibrated?
|
|
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
