Kenmore series 90 washer Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: 110.92591220	Brand: Kenmore	Age: 5 - 10 years
Previous Topic Next Topic

Glen Barclay		#1 Posted : Saturday, October 18, 2008 9:35:47 AM(UTC)
Rank: Member Groups: Registered Joined: 10/17/2008(UTC) Posts: 17		I need to replace the lid switch on my series 90 washer. The consol has two screws in the front (at an angle). I had removed these but still cannot figure out how to get the consol off and get the top of the machine off to access the switch.
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

libertyappl		#2 Posted : Saturday, October 18, 2008 11:22:19 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 8/13/2008(UTC) Posts: 3,097		There should be 2 clips, one on each side about 2 inches from the corners. You can use a putty knife to release these and raise the lid. Nat
User Profile View All Posts by User View Thanks

Drags1998		#3 Posted : Saturday, October 18, 2008 12:36:26 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/7/2008(UTC) Posts: 750		Remove the screws, pull console foward 1/2" and rotate over backwards, remove the 3 wire connector to the lid switch, remove the 2 GOLD colored clips, Tilt cabinet foward and slide off the washer.:)
User Profile View All Posts by User View Thanks

Glen Barclay		#4 Posted : Sunday, October 19, 2008 4:03:09 PM(UTC)
Rank: Member Groups: Registered Joined: 10/17/2008(UTC) Posts: 17		thanks for the information
User Profile View All Posts by User View Thanks

Glen Barclay		#5 Posted : Sunday, October 19, 2008 4:04:36 PM(UTC)
Rank: Member Groups: Registered Joined: 10/17/2008(UTC) Posts: 17		There does not appear to be any clips there. As I look at it there are plastic somethings at each corner.
User Profile View All Posts by User View Thanks

Gene		#6 Posted : Monday, October 20, 2008 10:38:19 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Hi Glen, These clips are #6 on the break down diagram. Insert a flat screwdriver into the front edge of the clip and pry back. - The part number for the lid switch is AP3094500 Gene.
User Profile View All Posts by User View Thanks

Glen Barclay		#7 Posted : Wednesday, October 22, 2008 9:06:20 AM(UTC)
Rank: Member Groups: Registered Joined: 10/17/2008(UTC) Posts: 17		Thanks for the great information. I am now in the final stages of putting the machine back together. I really appreciate all of the great info all of you have given me...
User Profile View All Posts by User View Thanks

Gene		#8 Posted : Wednesday, October 22, 2008 11:53:30 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		You are welcome. Keep us posted. Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)

Similar Topics

Kenmore series 90 washer stopped working (Washer Repair) by Guest 3/16/2024 6:19:45 AM(UTC)

Kenmore Series 90 Washer Agitates Clockwise (Washer Repair) by tomgf 10/30/2017 8:02:16 PM(UTC)

Kenmore series 90 washer spins while draining (Washer Repair) by Tbone4444 11/13/2014 11:03:16 AM(UTC)

Kenmore series 90 washer won't spin in Perm Press cycle (Washer Repair) by ozbirn 2/8/2013 3:56:30 PM(UTC)

Kenmore Series 90 Washer Not Draining but Does Spin (Washer Repair) by TaquacheDawg 3/28/2012 9:26:19 PM(UTC)

Kenmore Series 90 Washer - spin problems (Washer Repair) by dgb20 10/11/2011 4:10:07 PM(UTC)

Kenmore series 90 washer Control Knob (Washer Repair) by chiefjack 4/15/2011 7:19:53 AM(UTC)

Kenmore Series 90 washer (Washer Repair) by dguern1 7/10/2009 4:13:36 PM(UTC)