Crosley washes but only tries to spin. Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: CW5000W	Brand: Crosley	Age: 5 - 10 years
Previous Topic Next Topic

Ghite		#1 Posted : Saturday, September 22, 2007 2:35:58 PM(UTC)
Rank: Member Groups: Registered Joined: 9/22/2007(UTC) Posts: 2		My Crosley washer will not spin in the spin cycle it starts to spin but then stops and just agitates. The lid switch is working because the motor starts in the spin cycle and runs and the tub tries to turn slowly sometimes. It appears to be mechanical problem. Any ideas?
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

richappy		#2 Posted : Saturday, September 22, 2007 3:45:34 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		You probably have a bad thrust bearing washer. Will need to install a thrust bearing kit with pulley. Pull front panel off and turn tranny pulley in spin direction, opposite from agitate. If no spin, this confirms bad thrust bearing washer. Go to Appliance repairs, Appliancehelp, Appliances, repairs to dryers washers dishwashers fridges repairs microwaves ge maytag kenmore frigidaire westinghouse inglis, appliance how to take apart information, purchasing an appliance help, model number help, for directions, this is basically a Maytag washer so follow directions for a Maytag.
User Profile View All Posts by User View Thanks

Ghite		#3 Posted : Saturday, September 22, 2007 8:13:09 PM(UTC)
Rank: Member Groups: Registered Joined: 9/22/2007(UTC) Posts: 2		Thanks It sounds like that is the problem. I appreciate the information.
User Profile View All Posts by User View Thanks

richappy		#4 Posted : Sunday, September 23, 2007 1:22:05 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		The thrust assembly, when turned, pushes up a cam on the tranny pulley that releases the brake. If washers wear, the brake does'nt get released.
User Profile View All Posts by User View Thanks

richappy		#5 Posted : Sunday, September 23, 2007 1:22:55 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		The thrust assembly, when turned, pushes up a cam on the tranny spindle that releases the brake. If washers wear, the brake does'nt get released.
User Profile View All Posts by User View Thanks

dinki123		#6 Posted : Saturday, August 16, 2008 7:35:21 AM(UTC)
Rank: Member Groups: Registered Joined: 8/16/2008(UTC) Posts: 6		i replace with new kit ; how do you adjust. instruction not clear. is there a speacial tool to put clip back on easier. the shaft does not seem to stick out for enoug
User Profile View All Posts by User View Thanks

richappy		#7 Posted : Sunday, August 17, 2008 3:16:32 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		Wrap a towel around a piece of wood and stick it on top of the agitator, then force down the agitator by closing the lid and putting a toolbox on top. This should help: Also, pry the shaft down with a flat bladed screwdriver to allow insertion of the C clip.
User Profile View All Posts by User View Thanks

dinki123		#8 Posted : Sunday, August 17, 2008 6:22:14 AM(UTC)
Rank: Member Groups: Registered Joined: 8/16/2008(UTC) Posts: 6		when reinstall the thrust bearing : the is a plactic peice that goes on after the metal bearing. the pic show the ears pointing toward the agitatotor. is this corect. i put mine with the ears pointing toward the pulley. i was not the one who originally took apart so im not sure which way it came out thanks.
User Profile View All Posts by User View Thanks

richappy		#9 Posted : Sunday, August 17, 2008 8:22:49 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		The breakdown picture is usually right.
User Profile View All Posts by User View Thanks

dinki123		#10 Posted : Sunday, August 17, 2008 9:15:39 AM(UTC)
Rank: Member Groups: Registered Joined: 8/16/2008(UTC) Posts: 6		Ok Ill Try That Thank You Sooo Much
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (2)