Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
DIYMrC  
#1 Posted : Thursday, February 25, 2010 10:46:01 PM(UTC)
DIYMrC

Rank: Member

Groups: Registered
Joined: 2/9/2010(UTC)
Posts: 8

My GE gas dryer is taking longer to dry clothes, after the cycles ends clothes still damp in seams, pockets, thicker areas. I hear the burner ignite and it burns for about a minute and then shuts off. Then after 30 to 40 seconds, I hear the burner reignite and repeats the short burn cycle. Burner not on long enough to reach high heat. What is the problem and the fix? I hope an expert can help me out. Thanks!
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
magician59  
#2 Posted : Friday, February 26, 2010 8:02:11 AM(UTC)
magician59

Rank: Advanced Member

Groups: Senior Expert
Joined: 8/16/2007(UTC)
Posts: 3,273

Check for a clogged or restricted vent.
DIYMrC  
#3 Posted : Friday, February 26, 2010 8:55:43 AM(UTC)
DIYMrC

Rank: Member

Groups: Registered
Joined: 2/9/2010(UTC)
Posts: 8

Originally Posted by: magician59 Go to Quoted Post
Check for a clogged or restricted vent.


Will do. In the past I have cleaned the unit of lint, however, I only cleaned the front panel of the unit. Meaning the lint trap and blower areas. This time I will go further by removing the drum and clean the diffuser assembly. I suspect the dryer sheets cause the air path parts to become coated and therefore enabling lint to adhere to air path surfaces.
magician59  
#4 Posted : Friday, February 26, 2010 9:18:06 AM(UTC)
magician59

Rank: Advanced Member

Groups: Senior Expert
Joined: 8/16/2007(UTC)
Posts: 3,273

Pay particular attention to the external vent, especially if there is a long distance from your dryer to the outside. In my area, they build houses with the vents going through the roof...Arrrrggghhhh.
DIYMrC  
#5 Posted : Friday, February 26, 2010 9:45:05 AM(UTC)
DIYMrC

Rank: Member

Groups: Registered
Joined: 2/9/2010(UTC)
Posts: 8

Originally Posted by: magician59 Go to Quoted Post
Pay particular attention to the external vent, especially if there is a long distance from your dryer to the outside. In my area, they build houses with the vents going through the roof...Arrrrggghhhh.


I appreciate your suggestion, however, for my home the laundry is located in the garage and so the external vent is very short. The vent is immediately behind the unit. But I know what you mean, there are 2 story home out here and the laundry room located NOT adjacent to exterior walls so the exhaust vent path run through ceilings for over 12 ft. I suppose those vents would be cleaned ala chimney flues.
DIYMrC  
#6 Posted : Wednesday, March 3, 2010 11:22:56 PM(UTC)
DIYMrC

Rank: Member

Groups: Registered
Joined: 2/9/2010(UTC)
Posts: 8

Originally Posted by: DIYMrC Go to Quoted Post
I appreciate your suggestion, however, for my home the laundry is located in the garage and so the external vent is very short. The vent is immediately behind the unit. But I know what you mean, there are 2 story home out here and the laundry room located NOT adjacent to exterior walls so the exhaust vent path run through ceilings for over 12 ft. I suppose those vents would be cleaned ala chimney flues.


Did the job today and I did not find a lint blockage. There was quite a bit of lint build-up behind the blower fan. I removed the fan, and thoroughly cleaned out the lint. I also cleaned the fan in water and dish detergent. Cleaned the blower box and the exhaust pipe and the connector pipe to the external vent; no blockages found. The load was dry, and I used the normal time setting as I used to use. So far so good.
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.