Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
After rinse cycle is complete, the washer fails to drain.
Where to start?
Thanks, Island Joe
GE Profile Quiet Power II fails to drain
Model: GSD40204BB
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Joe,
Can you be more specific on the problem?
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
Hi Gene,
Thanks for the reply. The dishwasher completes a full cycle, cleaning well, but when it's over and you open the door, the bottom is still full of water.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Hi Joe,
The first thing I would check is the air gap (if there is one) on top of the sink. Remove the cover and the top piece and check for a clog.
Remove the drain hose form the air gap (or from the garbage disposer if there is no air gap), put the end of the hose in a bucket, run the drain cycle and watch for a foreign objects coming out.
If there is nothing wrong then it could be a kinked drain hose or a drain pump. For more accurate advise I need the complete model number of the dishwasher.
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
Hi Gene, Thanks for your note - the model is: GSD40204BB Joe
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Joe,
The model number consists of: 3 letters - 4 digits - 1 letter - 2 digits - 2 letters.
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
Hi Gene,
Sorry.
Model #: GSD 4040 Z 04 BB.
Joe
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Thank you, Joe
Do what I recommended first and post the results.
Gene.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
Hello Gene,
Sorry to be so long responding.
1) There is no air gap
2) no garbage disposal
3) drain from dishwasher connects directly to sink drain line, just above the elbow/trap
4) I disconnected the washer drain line from the sink drain line, partially filled the washer then hit reset to drain it. It did drain out of the dishwasher drain line, all over the cabinet and floor - no, just kidding - I had a bucket. All the water did drain into the bucket from the washer.
5) Reconnected drainline to sink line, ran a whole cycle with dirty dishes. Cleaned well, but.... the washer was full of water in the bottom that didn't drain after the cycle.
6) FYI, the sink the washer drain line hooks into drains ok, but not fantastic.
Do I have a ghost?
Joe
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 4/28/2008(UTC)
Posts: 6
|
Hello Gene,
Further checking.
I was able to make the dishwasher drain completely.
But only by starting a new normal cycle, then hitting reset after a 5 seconds and letting it drain. I had to repeat that process 5-6 times before it fully drained the washer. I had made sure the trap and line was completed clear first. Also, I was able to see a clear, seemingly normal, flow of draining using a flashlight to look down the sink drain. It's just that it took 5-6 reset cycles to give the pump enough time to empty the washer.
Must not be any clogging or kinking or even pump issue. A control issue of some sort?!
Joe
|
|
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
