Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Dryer runs, but no heat
Options
Go to last post Go to first unread
Model: KEYS850LE0 Brand: Kitchen Aid Age: 1 - 5 years
Previous Topic Next Topic
bluky  
#1 Posted : Sunday, December 20, 2009 8:07:20 AM(UTC)
bluky

Rank: Member

Groups: Registered
Joined: 12/20/2009(UTC)
Posts: 1
We have had our dryer for about 5 years. I runs, tub rotates and blower blows, but there is no heat. I have taken the back off and found the heater box. I have a repair manual, but it does not address troubleshooting the circuits. I understand there are a couple of fuses in the heater circuit, but don't know where they are. I have a multimeter. can you give me some direction on how to proceed and what elements to check?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Monday, December 21, 2009 1:36:52 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Replacement parts for WHIRLPOOL KEYS850LE0 | AppliancePartsPros.com

Here is the wiring diagram
http://www.servicematters.com/d...0Sheet%20-%203406681.pdf

First try flipping the breaker off/on slowly a couple times. Sometimes you can loose half the line without actually tripping the breaker and the heating coil requires the full 240 volts.
If this does nothing.
Measure the voltage at the plug
L1 to L2 should be 240 volts
L1 to Neutral and L2 to Neutral, both should be 120 volts.
If OK
Unplug the unit and check the wires at the unit's terminal strip to ensure they are properly connected and none of them have burned off
If OK
Plug the unit in and check the voltage at the terminal strip. This is just in case you have a bad line cord. Be careful 240 volts is lethal.
If OK
Unplug the unit and check the heating coil and thermostats etc. for continuity.
Heating coil, each side should be 20 ohms approximately.
Thermostats and thermal fuse all should be 0 ohms.

Be sure to disconnect one side of and device you are measuring this prevents reading an alternate/parallel circuit path. Also use your most sensitive ohms scale.
There is a good Sticky at the beginning of this forum on meter usage.
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (3)
Similar Topics
Dryer runs, but no heat (Dryer Repair)
by NightWolf999 3/13/2012 7:26:11 PM(UTC)
Dryer runs, but no heat (Dryer Repair)
by Lking444 12/15/2010 5:03:16 PM(UTC)
Dryer runs, but no heat (Dryer Repair)
by wrxnut25 9/12/2010 12:59:15 PM(UTC)
Gas Dryer Runs, but no heat (Dryer Repair)
by OKCandy 4/1/2009 5:41:52 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET