Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
No display on control pad after cleaning
Options
Go to last post Go to first unread
Model: MGR5730BDW Brand: Maytag Age: 5 - 10 years
Previous Topic Next Topic
margmcfarlane  
#1 Posted : Monday, December 14, 2009 12:10:09 PM(UTC)
margmcfarlane

Rank: Member

Groups: Registered
Joined: 12/14/2009(UTC)
Posts: 3
Hi:

I cleaned my LP gasMaytag oven last night and now there is nothing reading on the control pad and none of the touch buttons work. What is wrong and how do I fix it? The stove burners & igniters for same, light in the oven work fine. Have already tried turning the power off to the stove but that did nothing for the control pad. Occasionally the time comes up, flashing 12:00 but when I hit any of the touch pads, 12:00 disappears. Have also tried holding down both the clock pad and the cancel pad at the same time for 5 seconds as recommended by the guy at the Maytag service centre but that did nothing either.

Marg
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
Gene  
#2 Posted : Monday, December 14, 2009 2:08:05 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Marg,

Most likely the problem is a bad control board (aka a clock).

- The control board Part number: AP4428977
Back to top
margmcfarlane  
#3 Posted : Monday, December 14, 2009 5:40:26 PM(UTC)
margmcfarlane

Rank: Member

Groups: Registered
Joined: 12/14/2009(UTC)
Posts: 3
Thank you very much, Gene!

Marg
Back to top
Gene  
#4 Posted : Monday, December 14, 2009 6:06:27 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
You are welcome, Marg. Keep us posted.

Gene.
Back to top
Hammer and Chisel  
#5 Posted : Wednesday, January 6, 2010 3:45:57 PM(UTC)
Hammer and Chisel

Rank: Member

Groups: Registered
Joined: 1/6/2010(UTC)
Posts: 2
Hi,

Did replacing the Control panel work? I have the same situation and get a little nervous about such expensive parts.
Thanks
Ryan
Back to top
margmcfarlane  
#6 Posted : Wednesday, January 6, 2010 7:47:41 PM(UTC)
margmcfarlane

Rank: Member

Groups: Registered
Joined: 12/14/2009(UTC)
Posts: 3
Originally Posted by: Hammer and Chisel Go to Quoted Post
Hi,

Did replacing the Control panel work? I have the same situation and get a little nervous about such expensive parts.
Thanks
Ryan

Hi Ryan:

As it turned out, it's a loose wire somewhere in the wiring of the stove, not the control panel itself that is the problem. Discovered this when we moved the stove a little bit and up popped the control panel display! Have no idea where the wiring is loose as we're just keeping our fingers crossed that it continues to work as a repair guy wanted a small fortune to come out to our place in the country to try to find which wire it is. If it gives up the ghost again, we'll have to get someone out here but in the meantime, we're just using the stove and trying not to jar it!!

Best of Luck with yours,

Marg
Back to top
Hammer and Chisel  
#7 Posted : Thursday, January 7, 2010 4:58:08 AM(UTC)
Hammer and Chisel

Rank: Member

Groups: Registered
Joined: 1/6/2010(UTC)
Posts: 2
So kicking it might work after all.
Thanks,
Ryan
Back to top
Users browsing this topic
Guest (3)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET