Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
GE Electric Dryer Shuts Off Mid-Cycle
Options
Go to last post Go to first unread
Model: PTDN600EM2WT Brand: GE Age: 1 - 5 years
Previous Topic Next Topic
Dynocon  
#1 Posted : Thursday, October 22, 2015 5:20:00 PM(UTC)
Dynocon

Rank: Member

Groups: Registered
Joined: 10/22/2015(UTC)
Posts: 6
The dryer shuts off on both timed and moisture sensing settings, it will not immediately re-start but will after a few minutes.


I have checked the vent and it is clear with a lot of air flow.
I have taken the dryer apart, removed drum and vacuumed everything I can. Drum and motor turns fine and does not make any noise.

Does this sound like a bad motor or are there any other sensors that would shut it off?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
bizkid23  
#2 Posted : Friday, October 23, 2015 6:15:09 AM(UTC)
bizkid23

Rank: Advanced Member

Groups: Expert
Joined: 3/8/2010(UTC)
Posts: 22
Sounds like a bad motor for sure. When it cuts itself off the motor would probably be extremely hot and possibly even smell burnt (electrical smell).
Back to top
Dynocon  
#3 Posted : Friday, October 23, 2015 6:32:48 AM(UTC)
Dynocon

Rank: Member

Groups: Registered
Joined: 10/22/2015(UTC)
Posts: 6
Just wanting to confirm that no sensors would shut it off like this, thanks.
Back to top
Dynocon  
#4 Posted : Friday, October 23, 2015 6:53:03 AM(UTC)
Dynocon

Rank: Member

Groups: Registered
Joined: 10/22/2015(UTC)
Posts: 6
Just wanting to confirm that no sensors would shut it off like this, thanks.

Just kicked off again and the motor is very hot, hot enough to burn your finger so that must be it.
Back to top
bizkid23  
#5 Posted : Friday, October 23, 2015 6:16:34 PM(UTC)
bizkid23

Rank: Advanced Member

Groups: Expert
Joined: 3/8/2010(UTC)
Posts: 22
That is correct, the sensors would cut off heat not the motor. There are some sensors that kill power to the entire unit but it wouldn't come back on later as they are one time fuses.
Back to top
Dynocon  
#6 Posted : Friday, October 30, 2015 1:55:07 PM(UTC)
Dynocon

Rank: Member

Groups: Registered
Joined: 10/22/2015(UTC)
Posts: 6
New motor is installed, runs great, but now no heat.

The new motor came with a jumper harness to connect the old harness to the new motor connections, could it be in the harness?
Back to top
Dynocon  
#7 Posted : Sunday, November 1, 2015 12:43:59 PM(UTC)
Dynocon

Rank: Member

Groups: Registered
Joined: 10/22/2015(UTC)
Posts: 6
All the connection seem tight, took it apart, pushed on the wiring harness, did not move, was snapped in, decided to try again and it works. Something must have been loose.
Back to top
Users browsing this topic
Guest (4)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET