Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Dishwasher heating element trouble
Options
Go to last post Go to first unread
Model: WDF530PLYW6 Brand: Whirlpool Age: Less than 1 year
Previous Topic Next Topic
ziegism  
#1 Posted : Thursday, September 11, 2014 3:06:05 PM(UTC)
ziegism

Rank: Member

Groups: Registered
Joined: 9/11/2014(UTC)
Posts: 2
The dishwasher was not heating at all, and when I looked, I noticed the heating element was cracked. I ordered a new one, it still wasn't heating. I checked it with my multimeter and the ohms were reading way high, so I considered it defective and replaced it again. This newest one is still not heating. Could it be something else?

If so, how do I test to see what it is?

Thanks for any help.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Friday, September 12, 2014 1:50:45 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts.
Note that it is for a PLYW5.
PLWY6 did not come up.
Parts for Whirlpool WDF530PLYW5 / Dishwasher - AppliancePartsPros.com

See the attachment for the tech sheet

Could it be something else?
Yes it could.
Unplug the unit and check the hi-limit thermostat.
Should be 0 ohms.
If OK then check at the control board.
P4-4 to P4-3, you should see the heater resistance.
If not you have a bad connection/wire going down to the heater/hi-limit.
File Attachment(s):
WDF530.pdf (1,259kb) downloaded 20 time(s).
THIS FORUM IS DEAD!!!!!!!
Back to top
ziegism  
#3 Posted : Friday, September 12, 2014 2:44:55 AM(UTC)
ziegism

Rank: Member

Groups: Registered
Joined: 9/11/2014(UTC)
Posts: 2
Thanks so much. I really appreciate it.
Back to top
esd087  
#4 Posted : Tuesday, February 2, 2016 3:46:51 PM(UTC)
esd087

Rank: Member

Groups: Registered
Joined: 1/31/2016(UTC)
Posts: 3
Originally Posted by: denman Go to Quoted Post
Here are your parts.
Note that it is for a PLYW5.
PLWY6 did not come up.
Parts for Whirlpool WDF530PLYW5 / Dishwasher - AppliancePartsPros.com

See the attachment for the tech sheet

Could it be something else?
Yes it could.
Unplug the unit and check the hi-limit thermostat.
Should be 0 ohms.
If OK then check at the control board.
P4-4 to P4-3, you should see the heater resistance.
If not you have a bad connection/wire going down to the heater/hi-limit.


I know this is an older thread, but hopefully can get an answer. I have the WDF530PLYW5 and have been trying to figure out why it's not heating/drying.

Replaced the heating element, didn't work. Checked the hi limit thermostat, still good. Checking the board at P4-4 to P4-3, I have about 20ohms resistance. Is this GOOD? You said "you should see the heater resistance". So what else could it be?

Sorry if this is obvious - I'm very limited in my electrical knowledge.
Back to top
denman  
#5 Posted : Wednesday, February 3, 2016 1:32:30 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="Blue"]Checking the board at P4-4 to P4-3, I have about 20ohms resistance. Is this GOOD?[/COLOR]
Yes it is good.
Spec is 8 to 30 ohms so you are smack dab in the middle.

[COLOR="Blue"]So what else could it be?[/COLOR]
Since the heater si connected directly to the incoming line voltage through two relays odds are high that it is a bad control board.

I would check the thermistor resistance just to be sure it is OK before replacing the board.
See the WATER HEATING/HEAT DRY in the strip circuits section of the tech sheet.
THIS FORUM IS DEAD!!!!!!!
Back to top
swak6287  
#6 Posted : Tuesday, February 16, 2016 6:15:46 PM(UTC)
swak6287

Rank: Member

Groups: Registered
Joined: 2/16/2016(UTC)
Posts: 3
i tested the P4-4 AND P4-3 and i got nothing. It jsut show a "1". The P4-4 and P4-3 are the last 2 connectors on the board to the left, correct?
swak6287 attached the following image(s):
WIN_20160216_21_13_36_Pro.jpg
Back to top
denman  
#7 Posted : Wednesday, February 17, 2016 7:27:26 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Yes these connections are 3 and 4 but yoyu are not checking them correctly.

What you are trying to check is the heater and hi-limit so it is the connector that plugs into this that you want to check.

Take a look at the strip circuits in the tech sheet.
THIS FORUM IS DEAD!!!!!!!
Back to top
swak6287  
#8 Posted : Wednesday, February 17, 2016 7:43:07 AM(UTC)
swak6287

Rank: Member

Groups: Registered
Joined: 2/16/2016(UTC)
Posts: 3
Ah yes. Duh. Learning as I go. Thank you. I will check that tonight and report back.
Back to top
esd087  
#9 Posted : Wednesday, February 17, 2016 5:16:42 PM(UTC)
esd087

Rank: Member

Groups: Registered
Joined: 1/31/2016(UTC)
Posts: 3
Thanks for the advice. I ended up getting a control board on ******** and the dishwasher appears to be fully functional again.
Back to top
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET