Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Dishwasher quit working during a cycle
Options
Go to last post Go to first unread
Model: GU1200XTLS3 Brand: Whirlpool Age: 1 - 5 years
Previous Topic Next Topic
demortis1968  
#1 Posted : Friday, October 16, 2009 4:29:27 PM(UTC)
demortis1968

Rank: Member

Groups: Registered
Joined: 10/16/2009(UTC)
Posts: 3
My dishwasher quit working during a cycle. I don't get any lights on the display. The dishwasher is dead. There is electric getting to the unit. Please help.

Thank you.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Friday, October 16, 2009 5:39:28 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Replacement parts for WHIRLPOOL GU1200XTLS3 | AppliancePartsPros.com

See Item 6 in the "Control panel" section
THIS FORUM IS DEAD!!!!!!!
Back to top
demortis1968  
#3 Posted : Friday, October 16, 2009 8:28:46 PM(UTC)
demortis1968

Rank: Member

Groups: Registered
Joined: 10/16/2009(UTC)
Posts: 3
Originally Posted by: denman Go to Quoted Post
Here are your parts
Replacement parts for WHIRLPOOL GU1200XTLS3 | AppliancePartsPros.com

See Item 6 in the "Control panel" section



Denman,

Thank you very much for replying. I thought is was the fuse too but the fuse is good. I used my multi-meter and the fuse is NOT open. I also check both door close micro switches and they test good also. What else do you think it could be?? Any help is very much appricieated.

demortis1968
Back to top
denman  
#4 Posted : Saturday, October 17, 2009 3:36:48 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
This may help
https://secured.whirlpoo...520548/$FILE/8178022.pdf

Only a couple things:

1. Did you remove the fuse from the unit when you measured it? Also did you remove one wire from the switch? Please do not take offence but many people do not do this and they measure an alternate/parallel circuit path and it really confuses things.

2. Did you measure voltage at/on the board. A couple months ago I had a number of units where the wire nut connections were no good.

If you get power to the board and it does not fire up then the only thing I can think of is that the board is toast.
THIS FORUM IS DEAD!!!!!!!
Back to top
demortis1968  
#5 Posted : Saturday, October 17, 2009 1:27:26 PM(UTC)
demortis1968

Rank: Member

Groups: Registered
Joined: 10/16/2009(UTC)
Posts: 3
Denman,

Thanks again for the help. I did everything you said I should do. Now I need to make sure I am getting power to the board. Where should I place my voltmeter on the board to measure power to the board and what voltage should I be seeing?

Once again...thank you much.

demortis1968
Back to top
denman  
#6 Posted : Saturday, October 17, 2009 2:20:19 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I cannot make out the actual pin locations on the diagram but they are the W wire (lower right on the board in the diagram) as a common and then the line from the fuse and from the switch (switch closed) (both at top of board in the diagram). Both should give 120 volts
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (4)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2025, Yet Another Forum.NET