Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
ticat900  
#1 Posted : Monday, November 25, 2013 11:06:28 AM(UTC)
ticat900

Rank: Member

Groups: Registered
Joined: 11/25/2013(UTC)
Posts: 16

there is a noise suppressor/voltage distributer AP3009547
anyhow it blows as soon as I turn on the power supply breaker
also the control panel will not lite up?
Wiring seems correct and cant see any shorts etc.
any ideas? what is the idea of this suppressor?(function)
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
ticat900  
#2 Posted : Monday, November 25, 2013 11:47:30 AM(UTC)
ticat900

Rank: Member

Groups: Registered
Joined: 11/25/2013(UTC)
Posts: 16

Ok I found out what the suppressor does. If the suppressor blows up I assume it has too much voltage? and I assume it supplys the power to the control panel? anyone know?
denman  
#3 Posted : Tuesday, November 26, 2013 2:32:16 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Parts for Whirlpool KEBC107KSS05 Wall Oven - AppliancePartsPros.com

See the attachment for the wiring diagram.

The suppressor is supposed to filter any power voltage spikes to ground so that they do not blow the electronics on the control board.
It filters the L1 side of the line which also feeds the control board.

Very strange that they are blowing.
Has this unit ever worked OK with the current wiring set up?
If not then odds are there is either a hook up problem or a problem with the house wiring.

Check the power.
Check the voltage at the plug, usually ovens are hard wired so there is no receptacle.
L1 to L2 should be 240 volts
L1 to Neutral and L2 to Neutral, both should be 120 volts.
If OK
Unplug the unit and check the wires at the terminal strip in the machine to make sure none are loose or burned out
If OK
Check the power at the terminal strip.
Do this with the heater off and on.
Be careful as 240 volts is lethal !!!
File Attachment(s):
KEBC107K.pdf (314kb) downloaded 6 time(s).
THIS FORUM IS DEAD!!!!!!!
ticat900  
#4 Posted : Tuesday, November 26, 2013 6:36:12 AM(UTC)
ticat900

Rank: Member

Groups: Registered
Joined: 11/25/2013(UTC)
Posts: 16

Originally Posted by: denman Go to Quoted Post
Here are your parts
Parts for Whirlpool KEBC107KSS05 Wall Oven - AppliancePartsPros.com

See the attachment for the wiring diagram.

The suppressor is supposed to filter any power voltage spikes to ground so that they do not blow the electronics on the control board.
It filters the L1 side of the line which also feeds the control board.

Very strange that they are blowing.
Has this unit ever worked OK with the current wiring set up?
If not then odds are there is either a hook up problem or a problem with the house wiring.

Check the power.
Check the voltage at the plug, usually ovens are hard wired so there is no receptacle.
L1 to L2 should be 240 volts
L1 to Neutral and L2 to Neutral, both should be 120 volts.
If OK
Unplug the unit and check the wires at the terminal strip in the machine to make sure none are loose or burned out
If OK
Check the power at the terminal strip.
Do this with the heater off and on.
Be careful as 240 volts is lethal !!!


found out that stove was wired wrong.Was seeing 240V at filter.I assume this would have fried the control panel and most likely the lite transformer?
denman  
#5 Posted : Tuesday, November 26, 2013 7:50:19 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
The control panel may have survived but it would likely blew the control board. May have also blown the power transformer.

The light power supply may be OK if the door was closed when you applied power to it.
THIS FORUM IS DEAD!!!!!!!
ticat900  
#6 Posted : Tuesday, November 26, 2013 7:53:46 AM(UTC)
ticat900

Rank: Member

Groups: Registered
Joined: 11/25/2013(UTC)
Posts: 16

Originally Posted by: denman Go to Quoted Post
The control panel may have survived but it would likely blew the control board. May have also blown the power transformer.

The light power supply may be OK if the door was closed when you applied power to it.

whats the difference between the control panel and the control board?
are they not one and the same just slightly different way of description?
ticat900  
#7 Posted : Tuesday, November 26, 2013 8:26:22 AM(UTC)
ticat900

Rank: Member

Groups: Registered
Joined: 11/25/2013(UTC)
Posts: 16

Originally Posted by: denman Go to Quoted Post
The control panel may have survived but it would likely blew the control board. May have also blown the power transformer.

The light power supply may be OK if the door was closed when you applied power to it.



One repair idea was to check the thermal switch? but I don't see what the thermal switch has to do with the power supply/activation of the control panel
whats your thoughts on that idea.I did check wire in and wire out and it shows flow through continuity
denman  
#8 Posted : Tuesday, November 26, 2013 1:02:56 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Yes it may just be semantics.
The control board is the actual electronic control it is item 3 in section 02.
The control panel is the keypad, item 5 in section 03.

I also that the thermal switch (fuse) is not the problem as it just kills power to the oven elements.
THIS FORUM IS DEAD!!!!!!!
Users browsing this topic
Similar Topics
kitchenaid oven problem (Oven Repair (including Ranges and Cooktops))
by 08duramax 5/23/2012 12:10:07 AM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.