washer control panel all lights flashing -wont start - Appliance Repair Forum

Welcome Guest! You can not login or register.

Notification

Error

washer control panel all lights flashing -wont start Options Email this topic Watch this topic Print this topic » Normal Threaded
Model: WSSE4220A0WW	Brand: GE	Age: More than 10 years
Previous Topic Next Topic

gml		#1 Posted : Tuesday, May 21, 2013 4:35:27 PM(UTC)
Rank: Member Groups: Registered Joined: 5/21/2013(UTC) Posts: 2		The washer would not start despite showing power to the control panel. I replaced the control panel but now all the panel lights flash in synchrony constantly and the washer does not start. we pulled the plug and left it sit for 48 hours but the same thing is happening. Is there a ground somewhere? How to I fix? thanks


User Profile View All Posts by User View Thanks

Sponsor

See inside of your appliance - diagrams and part photos for virtually every model.

fairbank56		#2 Posted : Tuesday, May 21, 2013 5:37:55 PM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		Did you transfer the model select connector from the old control board to the new one? It's the connector with a single jumper wire on it. Eric


User Profile View All Posts by User View Thanks

gml		#3 Posted : Thursday, May 23, 2013 1:33:08 PM(UTC)
Rank: Member Groups: Registered Joined: 5/21/2013(UTC) Posts: 2		Originally Posted by: fairbank56 Did you transfer the model select connector from the old control board to the new one? It's the connector with a single jumper wire on it. Eric I do not know what that is. Where on the old control board is it located? A wiring diagram would help. We connected all wires that needed to be unplugged from the old control board to the new. thanks


User Profile View All Posts by User View Thanks

fairbank56		#4 Posted : Thursday, May 23, 2013 3:07:26 PM(UTC)
Rank: Advanced Member Groups: Expert Joined: 10/16/2012(UTC) Posts: 3,806 Was thanked: 7 time(s) in 7 post(s)		Next to the large transformer on the old circuit board there should be a connector with one or two jumper wires on it. This must be transfered to the new board. It is the model selector plug that tells the processor which model washer you have. The board can be used with different model washers. Eric


User Profile View All Posts by User View Thanks

waterpapa		#5 Posted : Sunday, December 8, 2013 8:25:21 AM(UTC)
Rank: Member Groups: Registered Joined: 12/8/2013(UTC) Posts: 1		Moving the plug from the old control panel to the new one fixed it, but mine had a total of 2 wires or four ends plugged into the jumper. Thanks so much for your assistance. The wife is happy again!!!!


User Profile View All Posts by User View Thanks

Guest		#6 Posted : Friday, July 21, 2023 12:54:43 PM(UTC)
Rank: Guest Groups: Joined: 8/10/2018(UTC) Posts: 0 Location: 99556 Was thanked: 4 time(s) in 4 post(s)		Mine didn’t have a jumper on the old board


User Profile View All Posts by User View Thanks

Guest		#7 Posted : Friday, July 21, 2023 12:56:50 PM(UTC)
Rank: Guest Groups: Joined: 8/10/2018(UTC) Posts: 0 Location: 99556 Was thanked: 4 time(s) in 4 post(s)		I need a picture of where next to the large transformer is


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (3)

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close