Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
GE Refrigerator - how do I get the old fresh door gasket off & new on? part# WR24x446
Options
Go to last post Go to first unread
Model: TBX21MA Brand: GE Age: More than 10 years
Previous Topic Next Topic
poolside4  
#1 Posted : Sunday, July 26, 2009 8:08:36 PM(UTC)
poolside4

Rank: Member

Groups: Registered
Joined: 7/26/2009(UTC)
Posts: 2
I can't see how to remove and replace the fresh door gasket on my GE refrigerator. The parts diagram shows a retainer strip but no way to get to it.
Any help?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
Bothcoasts Handyman  
#2 Posted : Monday, July 27, 2009 12:59:54 AM(UTC)
Bothcoasts Handyman

Rank: Member

Groups: Registered
Joined: 7/27/2009(UTC)
Posts: 11
There should be a strip over the screws that hold the magnetic seal in place. Usually you pry the strip up carefully to reveal the screws.

Good luck
Back to top
richappy  
#3 Posted : Monday, July 27, 2009 1:54:21 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
I would place the door on a flat surface and loosen all the screws, then pull off the old gasket, and put on the new. After installation, I put duck tape on the door to hold it in place, the door gasket will then pull in thus eliminating any gaps.Remove after a few hours.
Back to top
Bothcoasts Handyman  
#4 Posted : Monday, July 27, 2009 2:13:31 AM(UTC)
Bothcoasts Handyman

Rank: Member

Groups: Registered
Joined: 7/27/2009(UTC)
Posts: 11
I would leave the door on as you can do more damage than good when removing the screws with the old gasket. Clean the area very well. Place the new gasket in a oven warmed to 200 degrees. Then turn off. Place gasket inside. This will allow the gasket to form into the groove better.
I have tried it both ways and had the best results with the latter.
Back to top
richappy  
#5 Posted : Monday, July 27, 2009 2:31:28 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Sounds good, will try it next time.
Back to top
poolside4  
#6 Posted : Monday, July 27, 2009 1:44:33 PM(UTC)
poolside4

Rank: Member

Groups: Registered
Joined: 7/26/2009(UTC)
Posts: 2
Well, I used a hair dryer on the gasket to straighten out the edges. I don't trust myself with the oven. I noticed that there were no screw tabs or holes to install it. But, there was an arrowhead shaped bead running completely around the inside center line of the gasket . I took a chance and pulled on the old gasket and it came right away from the door. The bead sits in the retainer bracket center channel. I squared up the gasket on the door and pushed the bead into the channel. Worked like a charm. And it's a very tight seal!
Back to top
cookie87  
#7 Posted : Friday, September 4, 2009 12:41:12 PM(UTC)
cookie87

Rank: Member

Groups: Registered
Joined: 9/4/2009(UTC)
Posts: 4
Hmmm.. I'm in the midst of the same project on a Maytag with top freezer and the blow dryer did no good. How long did you blow dry? How powerful a blow dryer? I'm going to try the oven now....
Back to top
Users browsing this topic
Guest (3)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET