2 Pages12> Go to Page...

Electric Dryer Will Not Run W/o Holding In Start Button Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: 110.63952102	Brand: Kenmore	Age: 1 - 5 years
Previous Topic Next Topic

niggdj@bluemarble.net		#1 Posted : Friday, October 26, 2007 5:21:47 PM(UTC)
Rank: Member Groups: Registered Joined: 10/26/2007(UTC) Posts: 1		My Kennmore Elite Dryer Will Only Run While You Hold In The Start Button. Let Go Of The Button And It Stops Immediately. L.j.nigg
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

jdappl07		#2 Posted : Friday, October 26, 2007 6:21:43 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 10/22/2007(UTC) Posts: 81		bad motor for sure
User Profile View All Posts by User View Thanks

kawfeeman		#3 Posted : Thursday, December 13, 2007 7:30:08 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 12/13/2007(UTC) Posts: 323		For Sure !!
User Profile View All Posts by User View Thanks

richappy		#4 Posted : Sunday, December 16, 2007 2:43:38 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		Do not buy a new motor yet!!! If holding the start switch in, and the motor runs fine without drawing excessive current ( like over 8 amps) you have a good motor. If the motor start switch fails to switch to the run winding, you would hear a louder than normal motor hum!! Then smoke!!
User Profile View All Posts by User View Thanks

kawfeeman		#5 Posted : Sunday, December 16, 2007 8:58:56 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 12/13/2007(UTC) Posts: 323		just curious how this worked out ?
User Profile View All Posts by User View Thanks

bentwrench1999		#6 Posted : Thursday, December 20, 2007 7:37:18 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 12/14/2007(UTC) Posts: 72		You do have a relay in the console. I would check that 1st. Most whirlpool(kenmore) motors are pretty good. The relay # is AP3037419..wrench:)
User Profile View All Posts by User View Thanks

misterfixall		#7 Posted : Thursday, December 20, 2007 4:36:46 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 11/7/2007(UTC) Posts: 622		does drum turn when motor is running .if it does then its motor for sure
User Profile View All Posts by User View Thanks

joe shaffery		#8 Posted : Friday, December 21, 2007 12:49:36 PM(UTC)
Rank: Member Groups: Registered Joined: 12/21/2007(UTC) Posts: 5		whirlpool dryer same as kenmore problem =push start it operates let go it stops. how do i fix thanks joe s
User Profile View All Posts by User View Thanks

joe shaffery		#9 Posted : Friday, December 21, 2007 12:50:51 PM(UTC)
Rank: Member Groups: Registered Joined: 12/21/2007(UTC) Posts: 5		if u can't answer here my email is joets135@hotmail.com thanks again and happy holidays
User Profile View All Posts by User View Thanks

Gene		#10 Posted : Friday, December 21, 2007 12:59:30 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Hi niggdj Most likely the problem with you dryer is a bad control board. Normally it should sense the start of the motor and it does not. I've seen it many times before. - The part number for the control board is AP4319168 Good luck. Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (2)

2 Pages12> Go to Page...