Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
4 Pages123>»
Broiler Ignitor
Options
Go to last post Go to first unread
Model: KGST307FWHO Brand: Kitchen Aid Age: 1 - 5 years
Previous Topic Next Topic
Page  
#1 Posted : Saturday, December 15, 2007 6:30:40 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
Just replaced both ignitor bars ordered from here, great service and fast shipping!
AP2994572 (9751784) Ignitor, broil
AP2994573 (9751123) Ignitor, oven

Oven ignitor solved the baking problem, oven lights and heats up to temp.

Broil ignitor glows but fails to open gas valve, no broiler flame or clean since clean cycle starts with broil.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
Page  
#2 Posted : Sunday, December 16, 2007 2:01:45 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
Could the brand new broil ignitor be defective?

Or is there something else I am overlooking?

Gas valve works with new oven ignitor so i assume the valve is good.
Back to top
kawfeeman  
#3 Posted : Sunday, December 16, 2007 5:51:23 PM(UTC)
kawfeeman

Rank: Advanced Member

Groups: Senior Expert
Joined: 12/13/2007(UTC)
Posts: 323
just wondering if you have an amprobe to measure amperage draw of the broil ignitor ?
Back to top
Page  
#4 Posted : Sunday, December 16, 2007 7:38:38 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
Yes I can check the amp draw on that ignitor, I just assume it is correct being brand new. 3-3.2 is correct?
Back to top
Page  
#5 Posted : Sunday, December 16, 2007 7:40:11 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
If that is not the problem what else might be?
Back to top
kawfeeman  
#6 Posted : Sunday, December 16, 2007 7:54:53 PM(UTC)
kawfeeman

Rank: Advanced Member

Groups: Senior Expert
Joined: 12/13/2007(UTC)
Posts: 323
yea... i think 3.0 - 3.6 amp draw... just because it is new doesnt mean it is perfect ... has the broiler worked in the past ?
Back to top
Page  
#7 Posted : Sunday, December 16, 2007 7:58:57 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
If I swap leads on ignitors, will oven ignitor fool broil valve to open?
I realize that if this does work, gas will expell from broiler without lighting and will need to shut off before gas build up.

Will this test the broil circuit of valve or is there a continuity test for the broil side of valve that I can try instead?
Back to top
Page  
#8 Posted : Sunday, December 16, 2007 8:10:29 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
Yes broiler has worked in the past. Unit had problem when it was brand new, wire was pinched from factory and shorted that caused temp to rise beyond control and door to lock. The shorted wire was low voltage, I think it was temp sensor. Could not shut anything off on the controls at that point, had to pull plug and shut gas valve off to stop it.
Serviceman taped shorted wire and replaced control panel. Broiler worked after that, a year later the self-clean did not work, at which time I assumed broiler quit, not letting clean to work. It was out of waranty at that point so we stopped using the broiler and cleaned manually. Recently the oven ignitor whent out so I replaced both.
Back to top
kawfeeman  
#9 Posted : Sunday, December 16, 2007 8:17:52 PM(UTC)
kawfeeman

Rank: Advanced Member

Groups: Senior Expert
Joined: 12/13/2007(UTC)
Posts: 323
well not really necessary to swap wires with broil and bake ignitors... as long as you are getting 110vac to the broil ignitor and and you have checked to make sure the ignitor is drawing the correct amperage, are you sure the orifice is not clogged to the broil ?
Back to top
Page  
#10 Posted : Sunday, December 16, 2007 8:20:50 PM(UTC)
Page

Rank: Member

Groups: Registered
Joined: 12/15/2007(UTC)
Posts: 18
Where is that orifice?

There is a perforated panel that broil flame comes from, panel is removable.

Behind there?
Back to top
Users browsing this topic
Guest (5)
Similar Topics
no power to upper oven broiler ignitor (Oven Repair (including Ranges and Cooktops))
by Bill Patterson 2/9/2021 9:24:54 AM(UTC)
replaced broiler ignitor but still doesn't work well (Oven Repair (including Ranges and Cooktops))
by b*murphy 3/16/2015 1:00:58 PM(UTC)
Broiler ignitor (Oven Repair (including Ranges and Cooktops))
by greg@57 10/8/2012 1:02:44 PM(UTC)
Amana Broiler Ignitor Replacement (Oven Repair (including Ranges and Cooktops))
by HAWKE1023 1/2/2011 8:09:59 AM(UTC)
oven broiler ignitors (Oven Repair (including Ranges and Cooktops))
by Sammy D - Chicago 11/17/2010 7:33:07 AM(UTC)
Viking broiler ignitor problem (Oven Repair (including Ranges and Cooktops))
by skidgllfs 3/20/2009 5:36:40 AM(UTC)
oven/broiler ignitors (Oven Repair (including Ranges and Cooktops))
by glkearns 10/26/2008 1:47:51 PM(UTC)
Broiler Ignitor 4342528 (Oven Repair (including Ranges and Cooktops))
by Dennis49 5/9/2008 7:34:01 PM(UTC)
4 Pages123>»
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET