2 Pages<12 Go to Page...

Maytag Neptune Dryer Doesn't Start on /off Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: MDE5500AYW	Brand: Maytag	Age: 5 - 10 years
Previous Topic Next Topic

Appliance Ninja		#11 Posted : Wednesday, November 13, 2013 11:54:07 AM(UTC)
Rank: Member Groups: Registered Joined: 11/12/2013(UTC) Posts: 957		The diagrams are below. Appliance Ninja attached the following image(s):
User Profile View All Posts by User View Thanks

torrealtl1		#12 Posted : Wednesday, November 13, 2013 4:06:33 PM(UTC)
Rank: Member Groups: Registered Joined: 11/13/2013(UTC) Posts: 11		I verify both and they have continuity. What other part I need to verify?
User Profile View All Posts by User View Thanks

Appliance Ninja		#13 Posted : Wednesday, November 13, 2013 4:30:50 PM(UTC)
Rank: Member Groups: Registered Joined: 11/12/2013(UTC) Posts: 957		Okay, so let's get a look at the control board up top. Can you access the back of that board and look fro any poor connections or burnt solder joints on the back of the control, especially by any large relays (usually black and rectangular)?
User Profile View All Posts by User View Thanks

torrealtl1		#14 Posted : Wednesday, November 13, 2013 4:37:13 PM(UTC)
Rank: Member Groups: Registered Joined: 11/13/2013(UTC) Posts: 11		I verify the board and looks very good, also I disconnect the wire and connected again, but the problem still. The front panel continues turned on but when I pushed any of the push buttons doesn't works.
User Profile View All Posts by User View Thanks

Appliance Ninja		#15 Posted : Wednesday, November 13, 2013 4:45:09 PM(UTC)
Rank: Member Groups: Registered Joined: 11/12/2013(UTC) Posts: 957		Can you locate the gray wire that leads from the motor relay on the board to the motor and start the dryer while testing for 120 VAC between that gray wire and any metal on the dryer (ground), please?
User Profile View All Posts by User View Thanks

torrealtl1		#16 Posted : Wednesday, November 13, 2013 5:04:52 PM(UTC)
Rank: Member Groups: Registered Joined: 11/13/2013(UTC) Posts: 11		Do I need to perform this test with the Dryer connected to the power (electricity)?
User Profile View All Posts by User View Thanks

Appliance Ninja		#17 Posted : Wednesday, November 13, 2013 5:10:54 PM(UTC)
Rank: Member Groups: Registered Joined: 11/12/2013(UTC) Posts: 957		Yes, it will need to be plugged in, so be careful. We should see 120 VAC between that gray wire and ground when you push the start button. Let me know what happens, please.
User Profile View All Posts by User View Thanks

torrealtl1		#18 Posted : Wednesday, November 13, 2013 5:17:24 PM(UTC)
Rank: Member Groups: Registered Joined: 11/13/2013(UTC) Posts: 11		I did it in the motor relay with the grey wire and doesn't have continuity, meanwhile the black wire showed continuity with a ground.
User Profile View All Posts by User View Thanks

torrealtl1		#19 Posted : Wednesday, November 13, 2013 5:20:28 PM(UTC)
Rank: Member Groups: Registered Joined: 11/13/2013(UTC) Posts: 11		Thanks a lot for your help. I will continue tomorrow in this troubleshooting.
User Profile View All Posts by User View Thanks

Appliance Ninja		#20 Posted : Wednesday, November 13, 2013 5:20:39 PM(UTC)
Rank: Member Groups: Registered Joined: 11/12/2013(UTC) Posts: 957		Okay, so you show 120 volts to the black but not the gray? Did you hear the relay click still as you previously were?
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (2)

2 Pages<12 Go to Page...