Water Value Problem Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: SRD27S4W	Brand: Amana	Age: 5 - 10 years
Previous Topic Next Topic

bc4golf		#1 Posted : Tuesday, January 6, 2009 2:14:33 PM(UTC)
Rank: Member Groups: Registered Joined: 1/6/2009(UTC) Posts: 5		Installed a new water inlet value. The value is staying open to long letting in more water than needed to fill tray. The excess drains into ice storage bin, freezes and locks up dispenser. Do I have a faulty part? Incorrect part (FSP D7742204)? Can the part be calibrated for shorter open time?
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

Gene		#2 Posted : Wednesday, January 7, 2009 6:40:28 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Remove the front cover from the ice maker. There is a water level adjustment screw on the right side of the ice maker. Turn it CW for a half turn. Here are the break down diagrams for the Amana refrigerator Model SRD27S4W Gene.
User Profile View All Posts by User View Thanks

bc4golf		#3 Posted : Thursday, January 8, 2009 7:04:00 AM(UTC)
Rank: Member Groups: Registered Joined: 1/6/2009(UTC) Posts: 5		Is the front cover a snap on? Don't want to break something trying to fix something else. If water level adjustment doesn't work then assume a new ice maker is needed?
User Profile View All Posts by User View Thanks

icehouse		#4 Posted : Thursday, January 8, 2009 7:52:26 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/1/2008(UTC) Posts: 440		Originally Posted by: bc4golf Is the front cover a snap on? Don't want to break something trying to fix something else. If water level adjustment doesn't work then assume a new ice maker is needed? Pry off with a thin screwdriver. The adjustment screw is sideways with a phillips head. :)
User Profile View All Posts by User View Thanks

bc4golf		#5 Posted : Thursday, January 8, 2009 8:03:47 AM(UTC)
Rank: Member Groups: Registered Joined: 1/6/2009(UTC) Posts: 5		Ok, I am going to remove and replace the maker. The wiring harness is in the rear, very inexcessable my I add. Is there a snap retaining the harness or should it pull straight out?
User Profile View All Posts by User View Thanks

icehouse		#6 Posted : Thursday, January 8, 2009 8:22:37 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/1/2008(UTC) Posts: 440		Originally Posted by: bc4golf Ok, I am going to remove and replace the maker. The wiring harness is in the rear, very inexcessable my I add. Is there a snap retaining the harness or should it pull straight out? :confused: Why replace the icemaker if you only have a fill issue ?
User Profile View All Posts by User View Thanks

bc4golf		#7 Posted : Thursday, January 8, 2009 8:43:27 AM(UTC)
Rank: Member Groups: Registered Joined: 1/6/2009(UTC) Posts: 5		The IM heater, timer or something must be bad. The water run time is to long and the ice is not releasing. Water over flow is sufficent to freeze in bottom of bin and drsain into food section.
User Profile View All Posts by User View Thanks

icehouse		#8 Posted : Thursday, January 8, 2009 9:26:26 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/1/2008(UTC) Posts: 440		Originally Posted by: bc4golf The IM heater, timer or something must be bad. The water run time is to long and the ice is not releasing. Water over flow is sufficent to freeze in bottom of bin and drsain into food section. 1.The adjustment screw will control the amount of water fill. 2. The mold heater is replaceable. Why not remove the icemaker, empty it out and rinse it with warm water to be sure any ice in the mold is removed. Re-install the icemaker and check the operation. Cheaper than a new icemaker.
User Profile View All Posts by User View Thanks

bc4golf		#9 Posted : Friday, January 9, 2009 7:41:29 AM(UTC)
Rank: Member Groups: Registered Joined: 1/6/2009(UTC) Posts: 5		Thanks for your help. I didn't find the adjustment screw until I removed the IM. I was looking for a larger screw instead of a little white plastic one. Anyway, I found a new IM on the **** for $45 so I will install a new one. Hope that fixes the prob.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)