Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Kenmore Elite Flashing "Normal Wash" light. Will not Run/Reset/NADA!
Options
Go to last post Go to first unread
Model: 665.1726 Brand: Kenmore Age: 5 - 10 years
Previous Topic Next Topic
socaldave  
#1 Posted : Monday, September 27, 2010 7:28:57 AM(UTC)
socaldave

Rank: Member

Groups: Registered
Joined: 9/27/2010(UTC)
Posts: 4
I have a Kenmore Elite Ultrawash Quietguard 7. The "Normal Wash" LED just continuously flashes. Can NOT run diagnostic cycle. Unplug/Replug and nothing. I did remove the control panel and futzed around with the button membrane (one thread mentioned a sticky button might be the problem). Put all together and it looked like it tried to go into diagnostic cycle (all lights came on, etc.) but after a few moments, the dreaded "normal wash" LED flash again. Im leaning towards a new control panel..but not sure. Anyone else have a similar experience and was able to repair?? IM GETTING FRUSTRATED!! Thanks!
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Monday, September 27, 2010 10:12:01 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
The 665 prefix tells us it is actua;lly a Whirlpool unit but you are missing at least 4 digits at the end of your model number.
THIS FORUM IS DEAD!!!!!!!
Back to top
socaldave  
#3 Posted : Monday, September 27, 2010 10:17:13 AM(UTC)
socaldave

Rank: Member

Groups: Registered
Joined: 9/27/2010(UTC)
Posts: 4
Hi. yes, its a Kenmore (built by whirlpool). The complete model # is 665.17262401.
Back to top
socaldave  
#4 Posted : Monday, September 27, 2010 5:00:25 PM(UTC)
socaldave

Rank: Member

Groups: Registered
Joined: 9/27/2010(UTC)
Posts: 4
Diagnostic update: I was able to get the diagnostic mode to run. It ran through the cycles for about 15 minutes. Periodically, the "normal wash" did flash continuously, but then it would continue on with the next cycle.

Next step: I try to run a regular normal cycle. I hit the cancel/drain button twice and it seems to drain. Once it stops I press the normal wash button and it lights up. i press the start button and........NOTHING. It will not start. I try other wash cycle options (Pots/Pans, Quick Rinse, Smart Wash) all of those LEDs light up...but when I push the start button, the machine will not start.

So what do y'all think it might be???????

THanks!
Back to top
denman  
#5 Posted : Monday, September 27, 2010 5:18:43 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here is the tech sheet
http://www.servicematters.com/docs/wiring/Tech%20Sheet%20-%208535451.pdf

Often a blinking light is an indication of a stuck key
I would check the keypad with a meter.
THIS FORUM IS DEAD!!!!!!!
Back to top
socaldave  
#6 Posted : Tuesday, October 5, 2010 7:23:52 AM(UTC)
socaldave

Rank: Member

Groups: Registered
Joined: 9/27/2010(UTC)
Posts: 4
Just to close the loop on this problem....

Turns out it was the control panel membrane that was the culprit. I ordered a new control panel thru appliancepartspros and the dishwasher is up and running great!

Thanks for your help!

socaldave
Back to top
denman  
#7 Posted : Wednesday, October 6, 2010 1:49:42 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
You are welcome.

And thanks for getting back to us. Now when others search for a similar problem they will see what actually worked instead of just suggestions about what could be the cause.
THIS FORUM IS DEAD!!!!!!!
Back to top
RPicon  
#8 Posted : Wednesday, August 31, 2011 3:58:50 PM(UTC)
RPicon

Rank: Member

Groups: Registered
Joined: 8/31/2011(UTC)
Posts: 2
Originally Posted by: denman Go to Quoted Post
You are welcome.

And thanks for getting back to us. Now when others search for a similar problem they will see what actually worked instead of just suggestions about what could be the cause.


I replaced the control board but did not work for me. After I replaced it, it appeared to be working but got stuck on "wash cycle.", i.e. it kept washing. Now the "normal wash" light is blinking again. I’m not sure how to run the diagnose, there are no buttons for this. Hope you can help.
Back to top
denman  
#9 Posted : Friday, September 2, 2011 2:30:21 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
RPicon.

Please start your own thread (post) using "Post New Topic" adding to another person's post who has a different model number will just confuse things.
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET