Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
Hello All, We Had Notice The Temp Higher Then Normal.move Refrig Out, Fan Not Coming On?? I Can Turn Fan And It Will Spin .we Put A House Fan Behind Refrig Temp Comes Back Down.
Any Help Thank You In Advance
Thanks Brian
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert
Joined: 5/28/2008(UTC)
Posts: 1,620
|
Can you provide me a serial#.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
Hello, Thank You For Your Time.the S/n Is LL041263
Thank You Brian
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert
Joined: 5/28/2008(UTC)
Posts: 1,620
|
Let's find out if your fan or board is bad, disconnect the plug from the condenser fan and measure voltage from the red an white wire, you should have about 13volts DC,this is a dc motor so make sure you have your meter set on dc. If you have 13 volts replace the motor, if you don't have 13 volts, replace your board.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
Hello Again, I Had Changed The Fan,when I Would Spin It Would Keep Going Slow,so I Thought It Was The Fan. That Board, Is That The
Asm Main Control Board Up By The Water Filter ???
Thanks Again Brian
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert
Joined: 5/28/2008(UTC)
Posts: 1,620
|
It's on the back wall of the refer should be on the left side, behing a galvenized access panel
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
Hello. There Is 13.79 Vdc Red/white At The Plug Going To Motor.
No Fan
Then I Spin Fan By Hand And It Will Go Slow.looks Slow To Me
This Is A New Motor
What Is The Rpm Of Motor????
Wires At Motor X4 B,w,y,r
Wires At Plug X3 R,p,w
What Is Yellow Wire At Motor ????
Thanks For Your Help
Brian
|
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert
Joined: 5/28/2008(UTC)
Posts: 1,620
|
Yellow wire is not used on this model, you deffinatly need a new control board, and the good news is your board replacement is covered 100% by GE, There has been a high percentage of these boards failing, and your serial# falls into the board replacement program GE has going on. You wont have to pay anything as long as you call GE for service. When you call in let them no this is not cooling and you should have a tech there same day or next day.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/10/2008(UTC)
Posts: 9
|
Hello, Should I Put The Old Fan Back In,before I Call Them.
Thanks Again For Your Help
|
|
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
