3 Pages<123> Go to Page...

No power to dryer? Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: 86093800	Brand: Kenmore	Age: More than 10 years
Previous Topic Next Topic

Single Mom		#11 Posted : Tuesday, February 19, 2008 8:07:29 AM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		Blue was on COM Red was on NC White was on NO
User Profile View All Posts by User View Thanks

Gene		#12 Posted : Tuesday, February 19, 2008 8:34:30 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Connect the Blue and the White wires together. Gene.
User Profile View All Posts by User View Thanks

Single Mom		#13 Posted : Tuesday, February 19, 2008 9:05:40 AM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		Tried that and it still wont run gene. I put my meter on ac 250 and checked the outlet. I have a 4 pronged plug. I put red lead on one side and black in one of the round holes and I have no reading. I noticed in the breaker box the the dryer breaker does lock firmly into on position. Can this be my problem?
User Profile View All Posts by User View Thanks

Gene		#14 Posted : Tuesday, February 19, 2008 9:10:38 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		No doubt the problem is there. You have to call a certified electrician to replace the breaker. Gene.
User Profile View All Posts by User View Thanks

Single Mom		#15 Posted : Tuesday, February 19, 2008 9:21:01 AM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		Thank you so much for all your help. I have learned so much from you and appreciate all this new knowledge. No doubt I will be back to this site! Thank you again!!!!
User Profile View All Posts by User View Thanks

Single Mom		#16 Posted : Tuesday, February 19, 2008 3:49:16 PM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		Dryer up and running again. Slight problem though, I dropped a screwdriver bit to my drill down the link screen vent and its lodged in the track where the screen slides. Banged and banged....turned the dryer over....nothing. Its alittle beyond where the vent curves and my hand can no loner reach, even with a screw driver in hand I couldnt pop it out.
User Profile View All Posts by User View Thanks

Gene		#17 Posted : Tuesday, February 19, 2008 4:03:01 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		You have to remove the rear cover and the air duct (on the left). You can not remove the air dust completely without disassembling the whole dryer but you can lift the bottom of the air duct which should be good enough to reach this piece. Try to use a magnet. Gene.
User Profile View All Posts by User View Thanks

Single Mom		#18 Posted : Sunday, February 24, 2008 10:55:11 AM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		:) :) :) thank you so much. I didnt think there was access on the air duct but when jacked it up a bit I saw the large hole. It was big enough for me to wedge a screwdriver behind the lodged item and free it. Plus I found a lost tool !!!!!!!! You have taught me so much about my dryer I might just keep it for another 20 yrs! Have a wonderful day, thanks again!
User Profile View All Posts by User View Thanks

Gene		#19 Posted : Sunday, February 24, 2008 11:37:17 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		I'm glad you were able to fix it. Gene.
User Profile View All Posts by User View Thanks

Single Mom		#20 Posted : Thursday, March 6, 2008 12:36:48 PM(UTC)
Rank: Member Groups: Registered Joined: 2/17/2008(UTC) Posts: 19		Same kenmore dryer, different problem. She won't heat up now. Runs but no heat. Maybe I should keep this dryer on a dolly for a few months? They say stuff like this runs in 3's. Any help appreciated.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)

3 Pages<123> Go to Page...