Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

New Topic Post Reply
Options
Go to last post Go to first unread
rainbow  
#1 Posted : Sunday, April 6, 2008 10:01:46 AM(UTC)
Quote
rainbow

Rank: Member

Groups: Registered
Joined: 4/6/2008(UTC)
Posts: 3

My dishwasher starts up with no problem and runs for about 20 minutes and then starts clicking at the same time every time and will not finish cycle regardless of which buttons i press. Any suggestions (contoller or float or other)?
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
rainbow  
#2 Posted : Sunday, April 6, 2008 10:04:54 AM(UTC)
Quote
rainbow

Rank: Member

Groups: Registered
Joined: 4/6/2008(UTC)
Posts: 3

any advise from maytag users
Gene  
#3 Posted : Monday, April 7, 2008 9:59:56 AM(UTC)
Quote
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Where this clicking is coming from - the control panel or the bottom of the dishwasher?

Gene.
rainbow  
#4 Posted : Monday, April 7, 2008 12:12:35 PM(UTC)
Quote
rainbow

Rank: Member

Groups: Registered
Joined: 4/6/2008(UTC)
Posts: 3

The clicking is coming from the control panel. The number flicks on and off with the clicking.
Gene  
#5 Posted : Monday, April 7, 2008 12:20:17 PM(UTC)
Quote
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
The first thing I would do is replace the electronic control.

- The part number for the control assembly is AP3158622

Here are the break down diagrams for the Maytag dishwasher Model MDB9150AWB

Gene.
BeginnerGuy  
#6 Posted : Tuesday, April 8, 2008 7:13:01 PM(UTC)
Quote
BeginnerGuy

Rank: Member

Groups: Registered
Joined: 4/3/2008(UTC)
Posts: 16

I have a Maytag MDB9150AWW...similar model. The control board died about a week ago. I didn't have any clicking...I've posted elsewhere in the forum if interested.

If it is clicking in the upper door, I'd check to make sure the switches on the latch assembly are working. Just a thought.

Installing a control board isn't to difficult. I finished putting one in tonight. 1st, make sure power is turned off. Next, make a picture of where the wires plug in before you remove the defective board. This should be helpful when putting the new board in.

Based on suggestions from others, check the wiring harness for defects. I found that there were a couple of wires where the plastic sheathing was cut through, but the copper wire looked unharmed. I found this down where the door hinges. It looked like a metal part from the door had been cutting into the wires somewhat. I'm not sure if this is what caused the control board to fail. Anyway, I used some electrical tape to tape up the wires, and then also to cover up and sharp metal edges.
Gene  
#7 Posted : Tuesday, April 8, 2008 7:20:05 PM(UTC)
Quote
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Thank you BeginnerGuy,

Very useful advise.

Gene.
Quick Reply Show Quick Reply
Users browsing this topic
New Topic Post Reply
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.