Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
scottfr  
#1 Posted : Sunday, January 7, 2018 10:12:02 AM(UTC)
scottfr

Rank: Member

Groups: Registered
Joined: 1/7/2018(UTC)
Posts: 4

I was wondering if anyone can assist in diagnosing the problem with my maytag washer, it is a top loading Maytag, model number SAV4655EWW

The washer won't spin or drain. It will go to the end of the wash cycle with a tub full of water. After the wash cycle completes, (without draining or spinning) the tub left full of water. I am able to get it to spin and drain by restarting a spin cycle, it will then drain and spin. However, after successfully draining, if I start a brand new cycle, the cycle ends again with the tub full of water.

Please note, that the the machine DOES cycle through the stages, only it does not drain and spin. As stated above, I can get it to drain by going back to the spin cycle and re-starting it from there. Another way I found to get it to drain and spin is that if it is middle of the what would be a spin cycle, if I open and close the lid, the washer will then drain and spin one time, for that cycle.

Any assistance would be appreciated.
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
ThatGuy  
#2 Posted : Sunday, January 7, 2018 2:38:58 PM(UTC)
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
It could be your lid switch. Try opening and closing the lid the next time it stops. It might be bent or going bad internally. part no. 16

Parts for Maytag SAV4655EWW: Top and Door Switch Parts - AppliancePartsPros.com
scottfr  
#3 Posted : Sunday, January 7, 2018 5:03:47 PM(UTC)
scottfr

Rank: Member

Groups: Registered
Joined: 1/7/2018(UTC)
Posts: 4

Thank you!
scottfr  
#4 Posted : Sunday, January 28, 2018 9:37:04 AM(UTC)
scottfr

Rank: Member

Groups: Registered
Joined: 1/7/2018(UTC)
Posts: 4

unfortunately that did not resolve the problem. Any other possible recommendations?

Thanks in advance!

Regards,
Scott
scottfr  
#5 Posted : Saturday, February 3, 2018 8:32:49 AM(UTC)
scottfr

Rank: Member

Groups: Registered
Joined: 1/7/2018(UTC)
Posts: 4

Unfortunately that did not resolve the problem. Would you recommend anything else?

Thanks,
Scott
ThatGuy  
#6 Posted : Sunday, February 4, 2018 2:59:24 AM(UTC)
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
The next time it doesn't spin don't touch lid or anything else.

Reach over and grab the timer knob without pulling or pushing it in. Push it up, then to the right, then down, and then to the left.

If the motor comes on, the timer has bad contacts inside and will need to be replaced.
Users browsing this topic
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.