Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Kenmore Elite Dryer Intermittently Stops Running
Options
Go to last post Go to first unread
Model: 110.63952102 Brand: Kenmore Age: 1 - 5 years
Previous Topic Next Topic
CVilla  
#1 Posted : Tuesday, July 7, 2015 9:30:28 AM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
Kenmore Elite dryer intermittently stops running.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
CVilla  
#2 Posted : Tuesday, July 7, 2015 9:36:32 AM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
I can't seem to post more than a little bit at a time on here... For about a year now, my dryer randomly stops running. At first it was a few times a month, and progressively got worse. Now it shuts off 90% of the time.

It doesn't always shut off right away. Sometimes it runs for 5 to 10 minutes. This seems to be random as well. Today it would shut off immediately after releasing the start button. On the fourth or fifth attempt it ran for about 5 minutes. It's been running for about 10 minutes now, and still going.
Back to top
denman  
#3 Posted : Tuesday, July 7, 2015 11:08:09 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I am afraid that I cannot be very helpful since the fault is intermittent.

I can at least give you the tech sheet and perhaps some troubleshooting.

See the attachment for the tech sheet.

When it cuts out can you restart it right away or do you have to wait several minutes before it will restart.
If you have to wait then it could be that the motor is overheating. It's internal thermal protect opens and you have to wait for the motor to cool down and the protect to reset before it will restart.

Sounds more like there is a loose connection somewhere in the motor circuit.

I would start by unplugging the unit and checking the connections at the terminal strip.
If OK
Try swapping the heat and the motor relays. I think they are the same but double check this.

Perhaps try different cycle types just in case it is a bad spot on a set of timer contacts.

Have you tried running it with no clothes in it? Sometimes the door switch is just on the edge of closing so if the door gets pushed out a bit by the clothes it shuts the unit off.

With a little luck someone else ill jump in with better info for you.
File Attachment(s):
63952102.pdf (321kb) downloaded 32 time(s).
THIS FORUM IS DEAD!!!!!!!
Back to top
CVilla  
#4 Posted : Wednesday, July 8, 2015 7:52:13 AM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
When it cuts out, I usually can't just push start again to get it going. The dryer shuts off as soon as I release the button. To "reset" it, I have to rotate the timer past the off position and start over. Does that sound like a problem with the timer? I have the same problem whether I'm on timed dry, or moisture sensing.
Back to top
CVilla  
#5 Posted : Wednesday, July 8, 2015 7:53:48 AM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
Since the dryer stays running while holding down the start button, do you still think the door switch may be a problem?
Back to top
denman  
#6 Posted : Wednesday, July 8, 2015 8:22:51 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="Blue"]When it cuts out, I usually can't just push start again to get it going. The dryer shuts off as soon as I release the button. To "reset" it, I have to rotate the timer past the off position and start over. Does that sound like a problem with the timer? I have the same problem whether I'm on timed dry, or moisture sensing.[/COLOR]
It sounds more like a control board problem re: the board is not holding the motor relay closed. Going past off on the timer is probably resetting the board. But this is just the more likely of the two options.

[COLOR="Blue"]Since the dryer stays running while holding down the start button, do you still think the door switch may be a problem?[/COLOR]
No. If the door switch was open the unit would stop regardless of you holding the stat switch closed.
THIS FORUM IS DEAD!!!!!!!
Back to top
CVilla  
#7 Posted : Sunday, July 12, 2015 1:33:46 AM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
Finally got a multimeter, and it looks like the fabric care temperature switch may be the problem. One of the pins has no connectivity. I'm going to try replacing that and see what happens. Thanks for your help!
Back to top
fairbank56  
#8 Posted : Sunday, July 12, 2015 5:06:52 AM(UTC)
fairbank56

Rank: Advanced Member

Groups: Expert
Joined: 10/16/2012(UTC)
Posts: 3,806

Was thanked: 7 time(s) in 7 post(s)
A faulty temp switch would not cause the dryer to shut off.

Eric
Back to top
CVilla  
#9 Posted : Sunday, July 12, 2015 8:42:45 PM(UTC)
CVilla

Rank: Member

Groups: Registered
Joined: 7/7/2015(UTC)
Posts: 6
I'm not sure where to go from here then. Everything else seems to be working correctly. If it's something like the control board going out, I'd probably just scrap the dryer and get a new one. It costs more than the dryer is worth.
Back to top
denman  
#10 Posted : Tuesday, July 14, 2015 2:35:04 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
If everything else checks out OK then all that is left is the control board.
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (4)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET