Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

2 Pages<12
Options
Go to last post Go to first unread
gesche444  
#11 Posted : Saturday, August 2, 2014 9:55:22 AM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

picture of control panel
gesche444 attached the following image(s):
IMG_2571 10x6.jpg
richappy  
#12 Posted : Sunday, August 3, 2014 1:22:10 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Try thawing it out with a hair dryer.
gesche444  
#13 Posted : Sunday, August 3, 2014 4:58:11 AM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

Sorry! Do not understand your suggestion. How does thawing with a hairdryer help in removing at control panel? Of course it is early in the morning. According to what I have read, you should push up on the panel and pull out to remove. No ice here to thaw. Appreciate your help
richappy  
#14 Posted : Sunday, August 3, 2014 8:52:25 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
The hair dryer will make the inner plastic softer and make it easier to remove the cover.
gesche444  
#15 Posted : Sunday, August 3, 2014 10:50:18 AM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

OK. I am looking at the solenoid. Check out the pictures. I see rust and some wet spots
gesche444 attached the following image(s):
IMG_2577.jpg
IMG_2575.jpg
IMG_2574.jpg
gesche444  
#16 Posted : Sunday, August 3, 2014 11:28:36 AM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

As the screws are rusted, where can I find a diagram with part numbers for ordering replacement screws for the solenoid and ice dispenser door? What about the moisture around the door and solenoid? Is wiping it dry good enough?
gesche444  
#17 Posted : Sunday, August 3, 2014 1:25:36 PM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

Picture of screws that I need a part number
gesche444 attached the following image(s):
IMG_2574 WHITE CIRCLES.jpg
gesche444  
#18 Posted : Monday, August 4, 2014 6:42:45 AM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

Solenoid really rusted. Not sure where the water came from or how. See pictures.
gesche444 attached the following image(s):
IMG_2581 10x 150ppi.jpg
IMG_2582 10x 150ppi.jpg
IMG_2583 10x 150ppi.jpg
gesche444  
#19 Posted : Monday, August 4, 2014 3:27:29 PM(UTC)
gesche444

Rank: Member

Groups: Registered
Joined: 3/29/2009(UTC)
Posts: 23

Installed the new solenoid and plunger. Works much better, however the ice dispenser door remains open. When touched it closes. Before, it would not close even with coaxing. So long as I remember to reach my hand to the door and touch it so it closes shut, it will hopefully not warm up the freezer. I consider it 90% fixed. Would not be satisfied if this were some else's freezer.
Users browsing this topic
Guest (4)
Similar Topics
Frigidaire upright freezer to warm (Refrigerator & Freezer Repair)
by jrklund311 1/11/2024 2:51:18 PM(UTC)
freezer to warm and refrige, too (Refrigerator & Freezer Repair)
by Steve Gurd 12/8/2014 10:15:38 AM(UTC)
freezer to warm (Refrigerator & Freezer Repair)
by ron ump 3/30/2014 5:52:16 AM(UTC)
Freezer to warm during defrost (Refrigerator & Freezer Repair)
by zzski 2/15/2011 1:35:56 PM(UTC)
Freezer to warm (Refrigerator & Freezer Repair)
by SnoozenSusan 7/1/2010 9:57:57 AM(UTC)
Freezer to warm refer fine (Refrigerator & Freezer Repair)
by e63 2/19/2010 1:02:29 PM(UTC)
Fridge Freezer to warm (Refrigerator & Freezer Repair)
by kdbunn 8/31/2009 8:23:25 AM(UTC)
Freezer to warm (Refrigerator & Freezer Repair)
by Nblaylock 11/25/2008 9:12:59 AM(UTC)
2 Pages<12
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.