2 Pages<12 Go to Page...

Freezer to warm Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: PSS 26L GRC BB	Brand: GE	Age: 5 - 10 years
Previous Topic Next Topic

gesche444		#11 Posted : Saturday, August 2, 2014 9:55:22 AM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		picture of control panel gesche444 attached the following image(s):
User Profile View All Posts by User View Thanks

richappy		#12 Posted : Sunday, August 3, 2014 1:22:10 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		Try thawing it out with a hair dryer.
User Profile View All Posts by User View Thanks

gesche444		#13 Posted : Sunday, August 3, 2014 4:58:11 AM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		Sorry! Do not understand your suggestion. How does thawing with a hairdryer help in removing at control panel? Of course it is early in the morning. According to what I have read, you should push up on the panel and pull out to remove. No ice here to thaw. Appreciate your help
User Profile View All Posts by User View Thanks

richappy		#14 Posted : Sunday, August 3, 2014 8:52:25 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		The hair dryer will make the inner plastic softer and make it easier to remove the cover.
User Profile View All Posts by User View Thanks

gesche444		#15 Posted : Sunday, August 3, 2014 10:50:18 AM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		OK. I am looking at the solenoid. Check out the pictures. I see rust and some wet spots gesche444 attached the following image(s):
User Profile View All Posts by User View Thanks

gesche444		#16 Posted : Sunday, August 3, 2014 11:28:36 AM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		As the screws are rusted, where can I find a diagram with part numbers for ordering replacement screws for the solenoid and ice dispenser door? What about the moisture around the door and solenoid? Is wiping it dry good enough?
User Profile View All Posts by User View Thanks

gesche444		#17 Posted : Sunday, August 3, 2014 1:25:36 PM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		Picture of screws that I need a part number gesche444 attached the following image(s):
User Profile View All Posts by User View Thanks

gesche444		#18 Posted : Monday, August 4, 2014 6:42:45 AM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		Solenoid really rusted. Not sure where the water came from or how. See pictures. gesche444 attached the following image(s):
User Profile View All Posts by User View Thanks

gesche444		#19 Posted : Monday, August 4, 2014 3:27:29 PM(UTC)
Rank: Member Groups: Registered Joined: 3/29/2009(UTC) Posts: 23		Installed the new solenoid and plunger. Works much better, however the ice dispenser door remains open. When touched it closes. Before, it would not close even with coaxing. So long as I remember to reach my hand to the door and touch it so it closes shut, it will hopefully not warm up the freezer. I consider it 90% fixed. Would not be satisfied if this were some else's freezer.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (6)

Similar Topics

Frigidaire upright freezer to warm (Refrigerator & Freezer Repair) by jrklund311 1/11/2024 2:51:18 PM(UTC)

freezer to warm and refrige, too (Refrigerator & Freezer Repair) by Steve Gurd 12/8/2014 10:15:38 AM(UTC)

freezer to warm (Refrigerator & Freezer Repair) by ron ump 3/30/2014 5:52:16 AM(UTC)

Freezer to warm during defrost (Refrigerator & Freezer Repair) by zzski 2/15/2011 1:35:56 PM(UTC)

Freezer to warm (Refrigerator & Freezer Repair) by SnoozenSusan 7/1/2010 9:57:57 AM(UTC)

Freezer to warm refer fine (Refrigerator & Freezer Repair) by e63 2/19/2010 1:02:29 PM(UTC)

Fridge Freezer to warm (Refrigerator & Freezer Repair) by kdbunn 8/31/2009 8:23:25 AM(UTC)

Freezer to warm (Refrigerator & Freezer Repair) by Nblaylock 11/25/2008 9:12:59 AM(UTC)

2 Pages<12 Go to Page...