Whirlpool Double wall oven DEAD after self cleaning cycle rbd306pd- Page 2 - Appliance Repair Forum

Welcome Guest! You can not login or register.

Notification

Error

2 Pages<12

Whirlpool Double wall oven DEAD after self cleaning cycle rbd306pd Options Email this topic Watch this topic Print this topic » Normal Threaded
Model: RBD306PD	Brand: Whirlpool	Age: 5 - 10 years
Previous Topic Next Topic

wgbergman		#11 Posted : Sunday, January 19, 2014 10:33:50 AM(UTC)
Rank: Member Groups: Registered Joined: 1/18/2014(UTC) Posts: 3		This is probably a real dumb question. but where to you put the leads when measuring. Referencing the attached picture, I took the connector off of the right side. but I am not sure where to put the probe on the left side. the left side is attached to the control panel. Does touching the cylinder thing work? Thanks


User Profile View All Posts by User View Thanks

denman		#12 Posted : Monday, January 20, 2014 12:57:29 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 2/29/2008(UTC) Posts: 19,638 Thanks: 1 times Was thanked: 11 time(s) in 11 post(s)		You measure from the right hand side connector to the wire that runs to the control board connection. FYI: The fuse wires must be between the meter leads. The left side wire looks a little cruddy so you may have to scrape/sandpaper it a bit to get a good connection to the meter lead. Measuring to the fuse case is no good.
		THIS FORUM IS DEAD!!!!!!!


User Profile View All Posts by User View Thanks

wgbergman		#13 Posted : Monday, January 20, 2014 2:58:01 PM(UTC)
Rank: Member Groups: Registered Joined: 1/18/2014(UTC) Posts: 3		Thanks for the quick responce. I cleaned the wire and got and infinity reading. So the fuse needs to be replaced. I tried to gentle disconnect the fuse from the control board and it doesn't seem to want to come lose. I didn't want to force it. If i replace it and it still doesn't work, what are the next steps?


User Profile View All Posts by User View Thanks

denman		#14 Posted : Tuesday, January 21, 2014 12:10:24 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 2/29/2008(UTC) Posts: 19,638 Thanks: 1 times Was thanked: 11 time(s) in 11 post(s)		I think this is the fuse you need but double check with the parts people.You will need your model number. Part number: AP3777386 There is a pin that holds it in place in a plastic casing. Use a small flat head screw driver to push the pin flat to loosen it from the casing. Some release from the front others from the back of the connector, the following may help. How to remove pins from Male AMP-Universal Power connectors - YouTube How to remove/replace pins in harness connectors - DSM Forums
		THIS FORUM IS DEAD!!!!!!!


User Profile View All Posts by User View Thanks

Notis		#15 Posted : Tuesday, May 18, 2021 4:17:11 AM(UTC)
Rank: Member Groups: Registered Joined: 5/18/2021(UTC) Posts: 0 Location: VA		Our Whirlpool double oven is dead after self cleaning the bottom over. I saw your instructions for replacing the fuse but the door to the lower oven is locked. Anything I can do to open it?


User Profile View All Posts by User View Thanks

cnash		#16 Posted : Saturday, August 21, 2021 10:26:39 AM(UTC)
Rank: Guest Groups: Registered Joined: 8/10/2018(UTC) Posts: 0 Location: 99556 Was thanked: 4 time(s) in 4 post(s)		Gene #2 Post 14 years ago, thanks for posting this! I followed your advice, found the thermo fuse, checked it with a meter, and sure enough it was blown. You saved me tons of money. Was about to buy a new wall oven.


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest

2 Pages<12

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close