Frigidair Door Replacement - Appliance Repair Forum - Free Service from Appliance Parts Pros

Welcome Guest! You can not login or register.

Notification

Error

Frigidair Door Replacement Options Email this topic Watch this topic Print this topic » Normal Threaded
	Brand: Frigidaire	Age: 1 - 5 years
Previous Topic Next Topic

psamuel		#1 Posted : Tuesday, July 24, 2012 5:39:02 PM(UTC)
Rank: Member Groups: Registered Joined: 7/24/2012(UTC) Posts: 3		Model # PLGS389ECI. Issue is I can't replace the oven door. I was able to remove it, but I am having trouble reinstalling it. I have tried reversing the order. Making sure the tabs are up, sliding both hinge parts into their corresponding holes, lowering the door to 45 degrees and then trying to push the clips back into the slots to the loock the door in place. The trouble is with the last part. Any suggestions? I have looked at every video online and none of them seem to be the same as my hinge. Please help. thanks.


User Profile View All Posts by User View Thanks

Sponsor

See inside of your appliance - diagrams and part photos for virtually every model.

denman		#2 Posted : Wednesday, July 25, 2012 1:23:17 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 2/29/2008(UTC) Posts: 19,638 Thanks: 1 times Was thanked: 11 time(s) in 11 post(s)		Here is the operators manual. http://manuals.frigidaire.com/p...somption/318203876en.pdf [COLOR="Blue"]lowering the door to 45 degrees[/COLOR] It says to fully open the door, see page 17.
		THIS FORUM IS DEAD!!!!!!!


User Profile View All Posts by User View Thanks

psamuel		#3 Posted : Wednesday, July 25, 2012 1:08:53 PM(UTC)
Rank: Member Groups: Registered Joined: 7/24/2012(UTC) Posts: 3		Here's what is the challenge with the Oven Repalcement. I must have read the wrong instructions to take the door off. I missed the "lock the hinge" before removing part. Now I find it impossible to get teh spring loaded hinge parts to be in the correct alignment for replacement. Do you have any suggestions? Do I need to dissasemmble the door to reduce spring load??


User Profile View All Posts by User View Thanks

psamuel		#4 Posted : Wednesday, July 25, 2012 3:17:38 PM(UTC)
Rank: Member Groups: Registered Joined: 7/24/2012(UTC) Posts: 3		Ok. When I removed the door, I did not correctly lock the "clips" over the main hinge arms. So when I try to reinstall the door, I need to re-hook hte clips on the main hinge arms. Here's the problem. I found a video thta suggested tio try a pipe and bend the hinge arm down to meet up with the clip - problem is this hinge wants to bend under that much pressure. Any thoughts on how to "reload" the hinges so I can replace the oven door?:confused:


User Profile View All Posts by User View Thanks

denman		#5 Posted : Thursday, July 26, 2012 2:24:58 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 2/29/2008(UTC) Posts: 19,638 Thanks: 1 times Was thanked: 11 time(s) in 11 post(s)		Sorry but I do not have a better way than using a pipe. Perhaps re-post using Post New Topic with this specific question. With luck someone else will have an alternate method.
		THIS FORUM IS DEAD!!!!!!!


User Profile View All Posts by User View Thanks

kay edman		#6 Posted : Tuesday, September 4, 2018 12:42:44 PM(UTC)
Rank: Member Groups: Registered Joined: 1/9/2016(UTC) Posts: 8		Use the pipe to move the hinge AWAY from the bottom of the oven door. Then bring the clip UP to meet the unlocked hinge and hold it in place. Hope this helps.


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (4)

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close