Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
GE oven error codes
Options
Go to last post Go to first unread
Model: PROFILE Brand: GE Age: 1 - 5 years
Previous Topic Next Topic
bdeinhardt@aol.com  
#1 Posted : Thursday, June 25, 2009 5:47:37 AM(UTC)
bdeinhardt@aol.com

Rank: Member

Groups: Registered
Joined: 6/25/2009(UTC)
Posts: 3
What is F7 on a GE profile oven/convection oven?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Thursday, June 25, 2009 6:52:35 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
It is a GE which means that it is a pain to get any technical information on.

See the following link Page 3
http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/219-oven-error-codes.html

Looks like it indicates a stuck key.

Unplug the unit. Undo the ribbon cable. Plug the unit back in and see if the error re-occurs.
If it does they say the control board is bad.
If not then the keypad.
THIS FORUM IS DEAD!!!!!!!
Back to top
bdeinhardt@aol.com  
#3 Posted : Friday, July 3, 2009 7:18:49 AM(UTC)
bdeinhardt@aol.com

Rank: Member

Groups: Registered
Joined: 6/25/2009(UTC)
Posts: 3
So I did what you suggested--unplugged for a few minutes and plugged back in. The F7 was gone, but now I can't push the 2 or 3 button on the temperature panel. All the others are OK. That seems ominous. Ideas?
Back to top
denman  
#4 Posted : Friday, July 3, 2009 7:48:17 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
You did not include a Model Number so I do not know if the unit has a separate keypad and control board.

Often a keypad will use one common track for a number of keys, this could be why more than one key does not work.

If it does try the following
RIBBON CABLE CLEANING
Unplug the unit
Open it up
Remove the ribbon cable from the keypad to the control board at the control board.
Clean the edge connector.
If it is the type where there is not a connector just the insulation is removed, it can be cleaned with a pencil eraser. Do not use an ink eraser as it is too abrasive.
Check the tracks in the ribbon cable for hairline cracks. A magnifying glass helps here.
Would not hurt to clean the connector on the board. Use electronics contact cleaner or isopropyl alcohol and a tooth brush. Be gentle and do not reconnect till all the solvent evaporates.
Reconnect everything and give it a try.
THIS FORUM IS DEAD!!!!!!!
Back to top
bdeinhardt@aol.com  
#5 Posted : Friday, July 3, 2009 8:28:28 AM(UTC)
bdeinhardt@aol.com

Rank: Member

Groups: Registered
Joined: 6/25/2009(UTC)
Posts: 3
I am a bit technologically challenged. When you say "open it up" and "remove cable ribbon," (which requires knowing a calbe ribbon when I see one), will it be obvious/easy or should I get a repair person to come in and do it for me? Thanks so much for your help.
Back to top
denman  
#6 Posted : Friday, July 3, 2009 10:41:44 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
The ribbon cable will be obvious. It is a flat cable running from the control board to the keypad.

Be sure to unplug the unit when doing this.

If you feel uncomfortable, it may be best to get a service rep in.
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (2)
Similar Topics
GE Oven error codes (Oven Repair (including Ranges and Cooktops))
by BobChurch 9/1/2009 4:51:40 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET