Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
icandoitto  
#1 Posted : Wednesday, February 16, 2011 9:44:03 AM(UTC)
icandoitto

Rank: Member

Groups: Registered
Joined: 1/26/2011(UTC)
Posts: 2

I recently wrote about a problem with the oven control. There was no response to the up arrow touch pad for the oven and broiler temp control. When the oven temp is pushed the display read 000. When the oven temp up arrow was pushed nothing happened. Push the down arrow is pushed the temp read 350. from this point I could decrease the temp but not increase. Similarly pressing the broil button the display showed 000. Press the up arrow and no response. Press the down arrow and the display reads LO broil.

I was advised to replace the clock part 12001607 . Ordered from you folks and got terrific response (two days). Just installed it and when I touch the oven temp or broil buttons I get an F3 error message. Have tried turning off the power and restarting several times and continue to get the F3 message.

Would appreciate any thoughts you might offfer.
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
denman  
#2 Posted : Thursday, February 17, 2011 4:07:52 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I could not find any tech info on your specific model.

The 629 does tell us that it was made by Maytag.

When I look up fault codes the most common F3 for Maytags is an oven sensor problem so that is where I would start. Perhaps you did not get the plug seated correctly on the new control board.

Here is a link, check out 7, 8, 20 and 21.
http://www.applianceaid.com/elecrange.html
THIS FORUM IS DEAD!!!!!!!
icandoitto  
#3 Posted : Thursday, February 17, 2011 5:44:58 PM(UTC)
icandoitto

Rank: Member

Groups: Registered
Joined: 1/26/2011(UTC)
Posts: 2

Originally Posted by: denman Go to Quoted Post
I could not find any tech info on your specific model.

The 629 does tell us that it was made by Maytag.

When I look up fault codes the most common F3 for Maytags is an oven sensor problem so that is where I would start. Perhaps you did not get the plug seated correctly on the new control board.

Here is a link, check out 7, 8, 20 and 21.
http://www.applianceaid.com/elecrange.html

Thanks for your reply . I went back in and rchecked the seating of the plugs and it did the trick
denman  
#4 Posted : Friday, February 18, 2011 2:53:00 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
You are welcome.


And thanks for getting back to us. Now when others search for a similar problem they will see what actually worked instead of just suggestions about what could be the cause.
THIS FORUM IS DEAD!!!!!!!
Users browsing this topic
Guest (4)
Similar Topics
Oven control problems (Oven Repair (including Ranges and Cooktops))
by Eagar1 8/5/2012 12:31:05 PM(UTC)
Kitchen Aid Electric Range, Oven Control Problem (Oven Repair (including Ranges and Cooktops))
by pza 12/25/2011 6:26:16 PM(UTC)
Oven control problem (Oven Repair (including Ranges and Cooktops))
by PatinKY 1/3/2011 6:59:58 AM(UTC)
oven control problem please help ASAP (Oven Repair (including Ranges and Cooktops))
by renessabbd 12/22/2010 10:32:24 AM(UTC)
Oven control problem - HELP!! (Oven Repair (including Ranges and Cooktops))
by razorblade 12/30/2008 2:04:20 PM(UTC)
Admiral Electric Oven Control Problem (Oven Repair (including Ranges and Cooktops))
by stephenm38 11/8/2008 4:24:22 PM(UTC)
Oven Control Problem (Oven Repair (including Ranges and Cooktops))
by griggmi 11/10/2007 1:53:12 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.