Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Do it yourself
Options
Go to last post Go to first unread
Model: LSQ8000JQO Brand: Whirlpool Age: 5 - 10 years
Previous Topic Next Topic
GC Wilson  
#1 Posted : Tuesday, October 21, 2008 9:03:34 AM(UTC)
GC Wilson

Rank: Member

Groups: Registered
Joined: 10/21/2008(UTC)
Posts: 2
Replaced drive block and in the process of disassembly I pulled the water level hose from the switch and forgot to reconnect the hose after reassembly. Also since then I have replaced the lid switch like today. Water input won't shut off even when the lid is opened but machine operation stops such as spin and drain. The water level hose has been reconnected to the switch. Why won't the water input shut down at the correct level and when the lid is opened?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
v2k04  
#2 Posted : Tuesday, October 21, 2008 9:41:48 AM(UTC)
v2k04

Rank: Advanced Member

Groups: Senior Expert
Joined: 10/9/2008(UTC)
Posts: 784
The water will always fill whether the lid is closed or not make sure your tube doeen't have water in it make sure when it was reassembled the tube didn't get pinched or come off at both ends and also reset the water level switch. if it has a reset on the switch do it there. it will say reset on control panel if not,,,,,,,, putting the machine in spin and running it will reset the switch. All that is happening is the water level switch isn't getting satisfied to shut the water off at the level it's set on. so it continues to fill from now until eternity and the timer won't advance until contact is made in the switch which is what puts voltage to the timer so either the switch is bad or the tubing that hooks into it is piched or has come off since the switch works off air pressure
Back to top
GC Wilson  
#3 Posted : Thursday, October 23, 2008 10:14:59 AM(UTC)
GC Wilson

Rank: Member

Groups: Registered
Joined: 10/21/2008(UTC)
Posts: 2
Originally Posted by: v2k04 Go to Quoted Post
The water will always fill whether the lid is closed or not make sure your tube doeen't have water in it make sure when it was reassembled the tube didn't get pinched or come off at both ends and also reset the water level switch. if it has a reset on the switch do it there. it will say reset on control panel if not,,,,,,,, putting the machine in spin and running it will reset the switch. All that is happening is the water level switch isn't getting satisfied to shut the water off at the level it's set on. so it continues to fill from now until eternity and the timer won't advance until contact is made in the switch which is what puts voltage to the timer so either the switch is bad or the tubing that hooks into it is piched or has come off since the switch works off air pressure


I followed your instructions above, dialed timer to spin and it reset the switch. Washer works fine. Thanks for your help.

GC Wilson
Back to top
v2k04  
#4 Posted : Thursday, October 23, 2008 11:37:57 AM(UTC)
v2k04

Rank: Advanced Member

Groups: Senior Expert
Joined: 10/9/2008(UTC)
Posts: 784
you're very welcome
Back to top
Users browsing this topic
Guest (3)
Similar Topics
Do It Yourselfer (Washer Repair)
by Mark Finn 7/15/2009 3:42:54 PM(UTC)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET