Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

New Topic Post Reply
Options
Go to last post Go to first unread
houkden1  
#1 Posted : Tuesday, January 9, 2018 5:12:44 PM(UTC)
Quote
houkden1

Rank: Member

Groups: Registered
Joined: 1/9/2018(UTC)
Posts: 2

I have a bad Dryer Motor p/n 6 3060550-1 this part has been replaced by a Whirlpool p/n. The part I have been sent is a W10410893, which is the same motor, but it has a whole different wiring block on it and looks like I need another part. The connections on the wiring block are different than the ones in my machine and looks like I need some sort of a wiring connector plug which would fit in the new motor wiring block and connect to my old motor wires. It would be easy if the wires I have were the same size connectors (spades) as in the new wiring block, but they are not. Anyone have this problem and how can I solve this?:confused:
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
ThatGuy  
#2 Posted : Wednesday, January 10, 2018 12:44:16 AM(UTC)
Quote
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
According to the model number this should be the right motor and it should come with instructions on how to wire it.

Whirlpool W10411000 Motor-Drve - AppliancePartsPros.com
houkden1  
#3 Posted : Wednesday, January 10, 2018 5:33:52 AM(UTC)
Quote
houkden1

Rank: Member

Groups: Registered
Joined: 1/9/2018(UTC)
Posts: 2

That is my problem, after considerable digging around the internet, I figured out that the place I ordered the motor from, neglected to send wiring installation instructions and the three 1/8" shielded female connectors needed to do this install.

Thank you for your answer.
ThatGuy  
#4 Posted : Thursday, January 11, 2018 1:54:46 PM(UTC)
Quote
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
I used have several sets of those smaller terminals. They come with every replacement motor and 9 times out of 10, I was replacing a modern motor and I didn't need them. Its pretty crappy of them to keep the instructions and terminals. I hope you get it all sorted.

If that old motor has a pulley on it, make measurements and take pictures so you can get it in the right spot on the new motor.
rkinross  
#5 Posted : Saturday, March 10, 2018 10:36:16 AM(UTC)
Quote
rkinross

Rank: Member

Groups: Registered
Joined: 11/2/2011(UTC)
Posts: 3

Is there a part number for the wiring block that connects the new switch to the old motor wiring? Is there another way around this problem?
ThatGuy  
#6 Posted : Saturday, March 10, 2018 12:20:36 PM(UTC)
Quote
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
There is no wiring block. The new motor should have came with instructions and three crimp on terminals so you could adapt your old connectors to the new motor.
rkinross  
#7 Posted : Saturday, March 10, 2018 2:40:23 PM(UTC)
Quote
rkinross

Rank: Member

Groups: Registered
Joined: 11/2/2011(UTC)
Posts: 3

Thanks for the reply.

I have the Maytag SG1000 stack-able gas washer/dryer and the motor I thought I purchased is w10411000. What was sent was w10410893. It did not come with instructions or any special crimp on terminals.

The instructions I found on the internet follow:

grey wire Function L1 = 1/4 inch Thermal Protector Tab - remove blue jumper lead between switch terminal 4 and 1/4 inch Protector Tab. connect Grey Harness lead to 1/4 inch Protector Tab.

red wire function neutral = terminal number 5 - Reterminate Red and Blue Leads in the same 1/8 inch Insulated Terminal and Connect to Switch Tab 5. Connect the Blue Lead to 1/4 inch Tab 1.

blue wire function heater = terminal number 1 -

black wire function heater = terminal number 2 - Connect to 1/4 inch Tab 2

yellow wire function PushToStart (optional not present in machines with electronic controls - Reterminate Yellow Lead with 1/8 inch insulated Terminal and Connect to Switch Tab 6

Question: Do these special crimp on terminals have a part number and can they be purchased?

Thanks
ThatGuy  
#8 Posted : Saturday, March 10, 2018 11:06:01 PM(UTC)
Quote
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
Somebody is jerking you around. Look at the pics on this page. That stuff should all be inside the motor box.

Whirlpool W10411000 Motor-Drve - AppliancePartsPros.com
rkinross  
#9 Posted : Sunday, March 11, 2018 3:37:23 PM(UTC)
Quote
rkinross

Rank: Member

Groups: Registered
Joined: 11/2/2011(UTC)
Posts: 3

I am trying to post a message but keep getting an error:
80 Rejection set to: 20

Don't know what that means.
Quick Reply Show Quick Reply
Users browsing this topic
New Topic Post Reply
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.