Rank: Advanced Member
Groups: Moderators
Joined: 7/14/2010(UTC) Posts: 5,222
Was thanked: 1 time(s) in 1 post(s)
|
Originally Posted by: drazlou OK. Thanks for the help and the schematic. I'll give it a try and let you know. Drazlou, OK, Sounds like a deal to me. Just remember, the wire colors may be different, but the terminals and connections will be the same at the element and the new switch(per the previous wiring information). Will keep an eye out for your next post, Thanks,
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/8/2017(UTC) Posts: 10
|
Just looking at the schematic I see my error. I guessed that the blue wire on the left switch served the same purpose as the yellow on the right switch and connected it is if it was the outside burner. Its actually purple and is the common burner wire. The way I have it hooked up both burners are in series when I select the inner burner only which is why it's dim and voltage only to the outer burner when I select both burners. Thanks!
|
|
|
|
Rank: Advanced Member
Groups: Moderators
Joined: 7/14/2010(UTC) Posts: 5,222
Was thanked: 1 time(s) in 1 post(s)
|
Originally Posted by: drazlou Just looking at the schematic I see my error. I guessed that the blue wire on the left switch served the same purpose as the yellow on the right switch and connected it is if it was the outside burner. Its actually purple and is the common burner wire. The way I have it hooked up both burners are in series when I select the inner burner only which is why it's dim and voltage only to the outer burner when I select both burners. Thanks! Dazlou, You're Very Welcome !!! Good Luck,
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/8/2017(UTC) Posts: 10
|
Rewired the three burner wires per the schematic and it works fine. Thanks again for the help.
|
|
|
|
Rank: Advanced Member
Groups: Moderators
Joined: 7/14/2010(UTC) Posts: 5,222
Was thanked: 1 time(s) in 1 post(s)
|
Originally Posted by: drazlou Rewired the three burner wires per the schematic and it works fine. Thanks again for the help. Drazlou, GREAT !!! Glad you didn't damage anything. When you mis wire that switch, quite often it'll short out the internal contacts and it will need to be replaced. Thanks Again, Great job.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/12/2017(UTC) Posts: 2
|
I have a quick question. I have read the thread on the first page for the JES9800AAW. You say to connect the jumper wire from P1 to S1. On the switch I just ordered (part 12002125) there are two(2) P1 connector very close together. In which P1 connector should I connect the wire (see attached image)? The one on the left or the right (when the back switch is facing you) Thank you w2012z attached the following image(s):
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/8/2017(UTC) Posts: 10
|
Both are interconnected so it doesn't matter which terminal you put the jumper on. Use whichever one works better for you when you you have to connect all the other wires.
|
|
|
|
Rank: Advanced Member
Groups: Moderators
Joined: 7/14/2010(UTC) Posts: 5,222
Was thanked: 1 time(s) in 1 post(s)
|
Originally Posted by: drazlou Both are interconnected so it doesn't matter which terminal you put the jumper on. Use whichever one works better for you when you you have to connect all the other wires. Drazlou, Correct, it really doesn't matter which P1 terminal you use for the jumper wire. Always found it easier to install the jumper wire first, right out of the bag, then transfer and attach the wires to the switch terminals as directed in the instructions. If the red wire(s) need to be separated and attached to specific terminals, save that for last. Recheck all the connections, restore power, then test the switch and element operation*CAREFULLY*. Remove power and restore the product to operation, and recheck one more time.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 9/12/2017(UTC) Posts: 2
|
Thank you. Everything is now working.
|
|
|
|
Rank: Advanced Member
Groups: Moderators
Joined: 7/14/2010(UTC) Posts: 5,222
Was thanked: 1 time(s) in 1 post(s)
|
Originally Posted by: w2012z Thank you. Everything is now working. GREAT !!! We're glad you worked it out, and you're machine is up and running. Great Job. We're here if you need us. Thanks Again,
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close