Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
How to remove Electrolux ICON front panel
Options
Go to last post Go to first unread
Model: E23CS75DSS8 Brand: Electrolux Age: 5 - 10 years
Previous Topic Next Topic
exprexxo  
#1 Posted : Sunday, September 25, 2016 8:18:35 AM(UTC)
exprexxo

Rank: Member

Groups: Registered
Joined: 9/25/2016(UTC)
Posts: 3
There is a large bezel with no obvious points to put pressure for to release. I have removed the screws under the spill tray and have the little spill tray trim piece off
Parts for Electrolux E23CS75DSS8: Ice & Water Dispenser Parts - AppliancePartsPros.com

after that I am stumped and do not want to bend or scratch the metal.
I am looking to replace the water actuator which has broken

Thanks,

John
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
cbmserviceguy  
#2 Posted : Monday, September 26, 2016 7:21:28 AM(UTC)
cbmserviceguy

Rank: Member

Groups: Registered
Joined: 3/28/2016(UTC)
Posts: 200
Looks like there are two screws up from the bottom? Hard to tell from the diagram. Click your model number link and look at the dispenser diagram. The entire face piece comes off by itself. Looks like there are two screws up thru the lower lip of the opening and a bunch of plastic tabs as well I'm sure.
Back to top
exprexxo  
#3 Posted : Monday, September 26, 2016 6:39:13 PM(UTC)
exprexxo

Rank: Member

Groups: Registered
Joined: 9/25/2016(UTC)
Posts: 3
How can I detect the clips or where to push to remove them?
Back to top
cbmserviceguy  
#4 Posted : Wednesday, September 28, 2016 9:02:24 AM(UTC)
cbmserviceguy

Rank: Member

Groups: Registered
Joined: 3/28/2016(UTC)
Posts: 200
I've always just pulled, tugged and pried lightly to see where the sticking parts are. I have terrible luck with bezels and trim pieces though. If anybody else has better experience with them, please chime in and help out.
Back to top
exprexxo  
#5 Posted : Saturday, October 8, 2016 8:35:34 PM(UTC)
exprexxo

Rank: Member

Groups: Registered
Joined: 9/25/2016(UTC)
Posts: 3
Well your feedback was the best I could find and I was careful from your advice. So the bezel has tabs that are in slots in the door. After some time the metal was tight. I used a chisel on the inside edge to look in and saw the tabs. Then I took a piece of card board to protect door and then a piece of wood up at the bottom of the bezel and I tapped it with a hammer. After a few taps it came loose! So your were right after the two top screws and the three bottom screws it needed to go up a quarter inch. After that it all worked. We were careful not to pull fast or hard on the ribbon cable. Thanks for replying it really helped!
Back to top
ThatGuy  
#6 Posted : Saturday, October 8, 2016 9:18:10 PM(UTC)
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
There is a video on this page that shows how to get in there. Just in case somebody needs it.

Frigidaire 241688401 Ice Door Bracket - AppliancePartsPros.com
Back to top
ThatGuy  
#7 Posted : Saturday, October 8, 2016 9:19:12 PM(UTC)
ThatGuy

Rank: Advanced Member

Groups: Expert
Joined: 7/27/2010(UTC)
Posts: 1,395
United States
Location: near the middle of nowhere

Was thanked: 24 time(s) in 24 post(s)
Double posted because of site lag.
Back to top
Users browsing this topic
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET