Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

2 Pages<12
Options
Go to last post Go to first unread
Punisher Bass  
#11 Posted : Saturday, September 5, 2015 12:15:29 PM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

Nevermind, I figured it out, it's like the safety cap on a bottle of asprin, you have to press in and then unscrew. I'm running a test load right now, hopefully everything will go smoothly.
Punisher Bass  
#12 Posted : Saturday, September 5, 2015 2:35:24 PM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

I ran the test load and nothing has changed, it will fill with water and that's it, so unless this new timer is also bad I don't know what's going on. I don't know what the next step would be.
jon.wilob  
#13 Posted : Monday, September 7, 2015 8:27:16 PM(UTC)
jon.wilob

Rank: Member

Groups: Registered
Joined: 9/6/2015(UTC)
Posts: 9

Please post a pic. of the front of the timer that you can't get the knob off. I assume you checked for a set screw you need to loose in the knob to slide it off the shaft?
jon.wilob  
#14 Posted : Monday, September 7, 2015 8:31:04 PM(UTC)
jon.wilob

Rank: Member

Groups: Registered
Joined: 9/6/2015(UTC)
Posts: 9

Bypass your lid switch. Some washers won't allow even agitation, much less rinse/spin cycle if the lid switch is kaput.
Punisher Bass  
#15 Posted : Monday, September 7, 2015 8:39:56 PM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

I already posted that I got the knob off and timer swapped out. As for the lid switch, I know for a fact that mine will still agitate with the lid open, so I don't believe that's my problem.
Punisher Bass  
#16 Posted : Saturday, September 12, 2015 11:57:02 AM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

No progress on a solution, but I'm now wondering if it might be my motor start switch.
Punisher Bass  
#17 Posted : Sunday, September 27, 2015 12:39:54 PM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

I picked up a multimeter a few days ago, and once I figure out how to use it the right way, hopefully I'll be able to find out of it's a fault in the wiring harness or not.
Punisher Bass  
#18 Posted : Wednesday, September 30, 2015 1:09:25 PM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

Ok, according to the multimeter it's not a fault in the neutral wire. I put the leads to both ends and got 1.1-1.3, which I'm told is normal. So is it possible my motor start switch is just fried? That would explain the discoloration on the wiring harness wouldn't it?
Punisher Bass  
#19 Posted : Tuesday, October 13, 2015 11:55:49 AM(UTC)
Punisher Bass

Rank: Member

Groups: Registered
Joined: 7/10/2015(UTC)
Posts: 32

Just reporting that I finally got the whole mess sorted out. After further testing it looked like the start switch was my problem the whole time. I ordered a new one and installed it and cleaned the inside of the contacts on the inside of the wiring harness just for good measure.

That was last week and I've run several loads since then, haven't had a single problem.
Users browsing this topic
Guest (4)
2 Pages<12
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.