Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
Whirlpool Duet Sport bearing out
Options
Go to last post Go to first unread
Model: WFW8300SW03 Brand: Whirlpool Age: 5 - 10 years
Previous Topic Next Topic
RobOnMV  
#1 Posted : Monday, September 15, 2014 3:02:37 PM(UTC)
RobOnMV

Rank: Member

Groups: Registered
Joined: 9/15/2014(UTC)
Posts: 3
Hello all,

I just had a repair tech come by and check out our washing machine. He said the bearing is gone, needed replacement, but he said it wasn't worth it as it was an all day repair, and I should just buy a new unit.

I'm finding it a bit hard to believe that taking off the back, replacing a bearing would be a $500+ repair, but I could be wrong.

Any thoughts?

Thanks in advance.
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
sidfink43  
#2 Posted : Monday, September 15, 2014 4:42:18 PM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
I assume your machine sounds like a jet engine in high spin. It probably is a $500.00 repair from a Whirlpool tech. The problem is that the bearing is pressed into the rear tub assembly and is not a separately repairable part. The rear tub assembly is a $200.00 part and does take a while to install, although $500.00 in total is pretty steep.

Unfortunately this problem is the bane of front loaders, and can occur for a number of reasons one of which is not using the right detergent.

Sorry for the bad news.
Back to top
RobOnMV  
#3 Posted : Monday, September 15, 2014 4:52:39 PM(UTC)
RobOnMV

Rank: Member

Groups: Registered
Joined: 9/15/2014(UTC)
Posts: 3
Thanks for the info - It was older, though certainly was hoping for more than 7 years out of it.

I asked him what brand/model he would get, or has, and he replied that he would probably get any direct drive top loader over any front loader.

Researching for a new washer now.

Thanks again.
Back to top
sidfink43  
#4 Posted : Monday, September 15, 2014 5:00:22 PM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
Good advice, I would say the same thing. Try to avoid anything with electronic controls, they contribute nothing and just cause expensive trouble.
Back to top
RobOnMV  
#5 Posted : Monday, September 15, 2014 5:09:13 PM(UTC)
RobOnMV

Rank: Member

Groups: Registered
Joined: 9/15/2014(UTC)
Posts: 3
funny - I left out that he also mentioned "direct drive top loader with knobs - no electronics".

Thanks
Back to top
sidfink43  
#6 Posted : Monday, September 15, 2014 5:12:24 PM(UTC)
sidfink43

Rank: Advanced Member

Groups: Senior Expert
Joined: 3/29/2009(UTC)
Posts: 11,699
Smart man - Good luck
Back to top
Users browsing this topic
Guest (2)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET