Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
lfshadow  
#1 Posted : Monday, August 12, 2013 6:33:40 PM(UTC)
lfshadow

Rank: Member

Groups: Registered
Joined: 2/20/2012(UTC)
Posts: 3

Kenmore Dryer Model #6091 (?)
Just replaced the heater element a week ago. Now it heats, but not very much. It takes 2+ hours to dry a load and by then the clothes smell sour. When I looked Up troubleshooting it said that one of several Thermostats might be out. How do I know which one to replace, or do I replace them all? And is there some way to Know if this is actually what’s wrong with it?
Thanks
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
denman  
#2 Posted : Tuesday, August 13, 2013 2:04:55 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Your model number is incomplete.
Kenmore/Sears numbers are usually 3 digits, a period and then an additional 8 digits.
Please check it.
Find your model number - AppliancePartsPros.com

[COLOR="Blue"]Why did you replace the heater?[/COLOR]
Your posts suggests that you had no heat at all but does not actually say that.

[COLOR="Blue"]How do I know which one to replace, or do I replace them all? And is there some way to Know if this is actually what’s wrong with it?[/COLOR]
Yes but we need a model number and then with luck we can find the wiring diagram for this unit. You can then troubleshoot the unit.

I would try the following first.
Poor venting is the most common cause of poor drying.

Unplug the unit and disconnect it from the vent system.
Now try a run.
If it now dries OK odds are the vent system needs checking/cleaning.
Be sure to check that the louvers on the outside of the house open correctly.

If you do not want any lint in the house.
Take a pair of pantyhose.
Put one leg into the other and then attach this to the dryer's vent.
Leave enough room so the pantyhose can balloon out like a windsock.

Both the above will let you check the temperature and the air flow.

Note: The above is not recommended for gas dryers due to carbon monoxide concerns.
THIS FORUM IS DEAD!!!!!!!
lfshadow  
#3 Posted : Tuesday, August 13, 2013 3:58:58 PM(UTC)
lfshadow

Rank: Member

Groups: Registered
Joined: 2/20/2012(UTC)
Posts: 3

Sorry 'bout that -
Model number 110.60901990
I had no heat at all a few weeks ago. So I replaced the heating element. Now it just gets warm, not hot.
The venting is good. I even replaced the venting to be sure, and checked the air flow outside. It was blowing plenty of slightly warm air.
I have the wiring diagram and all the other diagrams. If you want I can scan and send to you.

Thanks
HumboldtRepairMan  
#4 Posted : Tuesday, August 13, 2013 4:15:41 PM(UTC)
HumboldtRepairMan

Rank: Member

Groups: Registered
Joined: 7/16/2013(UTC)
Posts: 916

Check the cycling thermostat on the blower housing next to the thermal fuse that typically would be the problem......it should be 4 prong.....2 prongs ohm test at infinity and the other one has low resistance........continuity test this i bet it's your problem....even sometimes when they test good they get loose inside shake it see if it rattles..........here's your part:
Whirlpool 8318268 Dryer Cycle Thermostat - AppliancePartsPros.com
Users browsing this topic
Guest (4)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.