Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

Options
Go to last post Go to first unread
Daniel J  
#1 Posted : Saturday, April 4, 2009 11:59:01 AM(UTC)
Daniel J

Rank: Member

Groups: Registered
Joined: 4/3/2009(UTC)
Posts: 20

Kitchenaid dishwasher filler valve appears to be stuck on. Water overflowed out the door flooding the place, nice. I canceled the cycle and waited for the 2-minute timer to finish, but even after that was done fresh water is still flowing into the machine. Help.
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
applianceman  
#2 Posted : Saturday, April 4, 2009 2:22:34 PM(UTC)
applianceman

Rank: Member

Groups: Registered
Joined: 3/28/2009(UTC)
Posts: 1,648

If water continues to run after you open the door the water valve is bad and needs replacing. Cut the water off and order the valve. If it stops when you open the door the problem is electrical.
Daniel J  
#3 Posted : Saturday, April 4, 2009 4:31:51 PM(UTC)
Daniel J

Rank: Member

Groups: Registered
Joined: 4/3/2009(UTC)
Posts: 20

Yes the water kept running even with the dishwasher door open, and continued to run even after I turned the breaker off, so I will order the valve, thanks. Are the directions for replacing it included with the part?

And as long as I'm ordering parts for this dishwasher, I'm wondering about the rinse agent dispenser. It seems to me the manual said a full load of rinse agent is supposed to last 3 months but ours always seems to be gone in a matter of days even with the dial turned down to 2. Is this a common problem, and if so what's the solution?
Daniel J  
#4 Posted : Monday, April 6, 2009 12:08:20 PM(UTC)
Daniel J

Rank: Member

Groups: Registered
Joined: 4/3/2009(UTC)
Posts: 20

Bump... I was hoping to get these parts ordered today.

Can anyone advise if there is a solution to the rinse aid dispenser question above?
denman  
#5 Posted : Monday, April 6, 2009 12:35:30 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here is the tech sheet
http://www.servicematters.com/docs/wiring/wiring_main.htm

It looks like you have to order the complete assembly.
I would remove the inner door panel and check it,
A lot of dishwashers have had problems with rinse aid leaking out of the container and contaminating the wires in the door.
Check it over visually.
As long as it is not always powered on it is probably shot.
THIS FORUM IS DEAD!!!!!!!
Daniel J  
#6 Posted : Monday, April 6, 2009 10:32:34 PM(UTC)
Daniel J

Rank: Member

Groups: Registered
Joined: 4/3/2009(UTC)
Posts: 20

I looked behind the door panel and couldn't see any evidence of rinse aid leaking or residue on any of the wiring. So if it is actually leaking, I think it must be coming out the front.

I guess I'll dial it down to 1 and try to monitor it more carefully to see if it's really going through the supply too quickly. I've always found the little indicator window to be pretty useless at showing whether there's anything left, so maybe it just looks empty when it's really not.

I ordered the inlet valve to take care of the stuck-open problem, that was the most urgent thing. Thanks for the help.
richappy  
#7 Posted : Tuesday, April 7, 2009 1:26:51 AM(UTC)
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
It is rare a water solenoid fails like this. I would check the water pressure to the valve and look for foreign objects stuck in the valve screen. Low water pressure will cause a valve to stick open!
applianceman  
#8 Posted : Tuesday, April 7, 2009 5:50:14 AM(UTC)
applianceman

Rank: Member

Groups: Registered
Joined: 3/28/2009(UTC)
Posts: 1,648

I don’t disagree about the valve rarely going bad but if it does stick I would replace it. Because I wouldn’t risk flooding the kitchen again but if you do have a water pressure problem you need to fix that as well.
Daniel J  
#9 Posted : Tuesday, April 7, 2009 8:31:38 AM(UTC)
Daniel J

Rank: Member

Groups: Registered
Joined: 4/3/2009(UTC)
Posts: 20

The water pressure is great, in fact it was flowing into the tub (and subsquently onto the floor) at quite a healthy rate until I managed to cut off the supply. I ordered the new valve assembly already -- guess I'll see if there were any foreign objects when I pull the old one out.
Users browsing this topic
Guest (4)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.