Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

3 Pages123>
Options
Go to last post Go to first unread
wordbuilder  
#1 Posted : Sunday, June 24, 2012 2:18:02 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

CORRECTION TO SUBJECT LINE: Bosch hums for a moment THEN shuts off

When I start my Bosch SHE4AM12UC/01, the lights display as they should. It hums for a few moments (30 seconds to 1 minute), then illuminates the CLEAN light. This happens intermittently and with all cycles. According to the repairman, he cleaned the temperature sensor and replaced both control boards. Nevertheless, the problem persists. Any help on this would be appreciated. Thanks!
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
Gene  
#2 Posted : Monday, June 25, 2012 1:07:52 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Remove the toe panel and try to pinpoint that humming noise. Post the results.

Gene.
wordbuilder  
#3 Posted : Monday, June 25, 2012 2:06:02 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

I think the dishwasher may begin by pumping out any residual water. After that, it sounds like the pump that sprays the wash water engages. If I open the door at this point and pour in a couple of gallons of hot water, it sounds like it begins washing once I shut the door. About 50% of the time I do this, the dishwasher will then successfully complete all cycles.
Gene  
#4 Posted : Monday, June 25, 2012 4:17:37 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Originally Posted by: wordbuilder Go to Quoted Post
...I think the dishwasher may begin by pumping out any residual water...


Yes, that's right. But what about?
Quote:
...It hums for a few moments (30 seconds to 1 minute), then illuminates the CLEAN light...


We have to figure out where it's coming from.

Gene.
wordbuilder  
#5 Posted : Monday, June 25, 2012 6:31:20 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

I think the hum may be the sound of the pump for the wash water. It won't be until this weekend that I'm able to take it apart and investigate further.
wordbuilder  
#6 Posted : Saturday, June 30, 2012 10:39:42 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

Well, I pulled the bottom panel. With things clustered together the way they are, I am unable to tell what is making each sound. It takes about 2-1/2 minutes from pressing Start to the Clean light illuminating. (I think it is sometimes less than this.) Nevertheless, here's a video. Though there's not much to see, it will give you an idea of what I'm hearing.

Bosch Dishwasher Problem - YouTube
Gene  
#7 Posted : Monday, July 2, 2012 12:06:28 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Perform the troubleshooting as described in the attached Service manual. Post the results.

Gene.
File Attachment(s):
SHE4AM - SHX3.pdf (949kb) downloaded 159 time(s).
wordbuilder  
#8 Posted : Monday, July 2, 2012 7:30:04 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

Thanks, Gene. I hope I followed the correct steps. For "Customer Service Failure display," the LEDs for Active and Clean illuminate but both flash simultaneously, rather than being steady. The Customer Service Program completed successfully.
Gene  
#9 Posted : Tuesday, July 3, 2012 3:58:06 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert, Administrators
Joined: 7/19/2007(UTC)
Posts: 27,455

Was thanked: 4 time(s) in 4 post(s)
Try to run the dishwasher again.

Gene.
wordbuilder  
#10 Posted : Monday, July 9, 2012 12:34:24 PM(UTC)
wordbuilder

Rank: Member

Groups: Registered
Joined: 6/24/2012(UTC)
Posts: 11

I get the same results. It makes a bit of noise and then shuts off with the Clean light illuminated. Same 2 lights flash when I check the error codes.

I've come up with a bit of a workaround. It's tedious and I don't know how long it will continue to help. I pour a 1/2 gallon of hot water into the dishwasher and then start the cycle 3 minutes later. It exhibits the same problem behavior. Since the DW drains the water I put in, I dump in another 1/2 gallon of hot water and then start it immediately. It will usually run normally on the 2nd try but can take up to 4 total attempts, which is better than the 10 to 20 attempts it can take without dumping in hot water.
Users browsing this topic
Guest (4)
3 Pages123>
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.