2 Pages12> Go to Page...

Bosch Dishwasher Model SHE44C06UC/22 doesn't fill Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: SHE44C06UC/22	Brand: Bosch	Age: 1 - 5 years
Previous Topic Next Topic

nascarcoxy		#1 Posted : Sunday, June 10, 2012 1:09:12 PM(UTC)
Rank: Member Groups: Registered Joined: 6/10/2012(UTC) Posts: 7		My dishwasher will fill on the first cyle and run fine, after it drains it will not fill for any of the remaining cycles. I have switched out the control module and that didn't help. Anyone else run into this?
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

Gene		#2 Posted : Monday, June 11, 2012 1:46:24 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: nascarcoxy My dishwasher will fill on the first cyle and run fine, after it drains it will not fill for any of the remaining cycles. I have switched out the control module and that didn't help. Anyone else run into this? Remove the toe panel. Wait until it will get to that point. Remove the wires from the water inlet valve and check for 125 VAC between these wires while the control calls for water. Post the results. Gene.
User Profile View All Posts by User View Thanks

nascarcoxy		#3 Posted : Tuesday, June 12, 2012 12:23:05 PM(UTC)
Rank: Member Groups: Registered Joined: 6/10/2012(UTC) Posts: 7		Originally Posted by: Gene Remove the toe panel. Wait until it will get to that point. Remove the wires from the water inlet valve and check for 1250 VAC between these wires while the control calls for water. Post the results. Gene. If I did this right... the volts went from 121 down to 51.
User Profile View All Posts by User View Thanks

Gene		#4 Posted : Tuesday, June 12, 2012 4:23:58 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: nascarcoxy If I did this right... the volts went from 121 down to 51. How long time it was reading 121 VAC? Did the water go in while it was reading 121 VAC? Gene.
User Profile View All Posts by User View Thanks

nascarcoxy		#5 Posted : Wednesday, June 13, 2012 1:03:44 AM(UTC)
Rank: Member Groups: Registered Joined: 6/10/2012(UTC) Posts: 7		Originally Posted by: Gene How long time it was reading 121 VAC? Did the water go in while it was reading 121 VAC? Gene. I believe it was reading 51 while it was trying to fill..It still filled on the first cycle and during that time it read 121.
User Profile View All Posts by User View Thanks

Gene		#6 Posted : Wednesday, June 13, 2012 4:01:50 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		If there is improper voltage then the problem very likely is a bad control board. - The control board Part number: 676960 Gene.
User Profile View All Posts by User View Thanks

nascarcoxy		#7 Posted : Thursday, June 14, 2012 1:37:24 AM(UTC)
Rank: Member Groups: Registered Joined: 6/10/2012(UTC) Posts: 7		Originally Posted by: Gene If there is improper voltage then the problem very likely is a bad control board. - The control board Part number: 676960 Gene. I replaced that already and it still did the same thing....I will replace it again and see what happens.
User Profile View All Posts by User View Thanks

Gene		#8 Posted : Thursday, June 14, 2012 10:01:13 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Also would not hurt to check the wires between the control board and the water valve. Gene.
User Profile View All Posts by User View Thanks

nascarcoxy		#9 Posted : Sunday, June 17, 2012 5:26:22 PM(UTC)
Rank: Member Groups: Registered Joined: 6/10/2012(UTC) Posts: 7		Originally Posted by: Gene Also would not hurt to check the wires between the control board and the water valve. Gene. I replaced the contol module and checked the wires...this time it made it through the first two wash cycles and didn't fill on the third cycle and did fill on the fourth cycle.
User Profile View All Posts by User View Thanks

Gene		#10 Posted : Monday, June 18, 2012 12:31:42 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		This is very strange and points to some harness or loose connections problem. This is the worst possible thing which is very hard to diagnose. If you would not be able to diagnose it yourself, hire a pro. Good luck. Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)

2 Pages12> Go to Page...