5 Pages<12345> Go to Page...

Maytag Neptune Washer Shut off in mid cycle Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: MAH3000AWW	Brand: Maytag	Age: 5 - 10 years
Previous Topic Next Topic

jkoval		#21 Posted : Monday, April 5, 2010 8:05:04 PM(UTC)
Rank: Member Groups: Registered Joined: 2/24/2010(UTC) Posts: 5		Originally Posted by: Gene It can be removed from the back of the washer as well as from the front. 1/ Rear removal: Shut off the water to the inlet hoses and remove the hoses from the water valve connections of the washer. Remove the two ¼" hex head screws securing the water valve bracket to the cabinet. While pulling the lower end of the bracket down slightly, slide the bracket to the left. This will allow the injector hose to clear the rear cabinet opening. While pulling the bracket away from the cabinet, rotate the left side of the bracket away from the washer. 2/ Front removal: Remove the front panel. Remove dispenser bezel and raise the top cover to expose the upper rear cabinet area. I would prefer the rear removal. Gene. Gene is right, the rear is probably the easiest. I chose the front/top since I had it open aleady. You will probalby notice that the dispenser bezel/cover is cracked or cracks when you take it off. If you are comfortable with that, you have easy access to the wiring from the top. John
User Profile View All Posts by User View Thanks

supercliff		#22 Posted : Monday, April 9, 2012 10:58:17 AM(UTC)
Rank: Member Groups: Registered Joined: 4/9/2012(UTC) Posts: 9		I'm not sure if this thread is still active, but I have the same problem with my washer. I wanted to view the service bulletin, but the link is not working for me. Does anyone have a link to the service bulletin? (and/or have a "how to" on how to fix this issue) THANKS!
User Profile View All Posts by User View Thanks

Gene		#23 Posted : Tuesday, April 10, 2012 10:56:51 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Originally Posted by: supercliff I'm not sure if this thread is still active, but I have the same problem with my washer. I wanted to view the service bulletin, but the link is not working for me. Does anyone have a link to the service bulletin? (and/or have a "how to" on how to fix this issue) THANKS! Sorry for the broken link. The Service bulletin you were looking for is attached to the reply. Gene. File Attachment(s): Neptune stops in mid cycle.pdf (101kb) downloaded 24 time(s).
User Profile View All Posts by User View Thanks

supercliff		#24 Posted : Tuesday, April 10, 2012 9:33:28 PM(UTC)
Rank: Member Groups: Registered Joined: 4/9/2012(UTC) Posts: 9		Originally Posted by: Gene Sorry for the broken link. The Service bulletin you were looking for is attached to the reply. Gene. Thanks Gene! I have the type of washer with the dryer on top (both front load). I know how to open up the front panels (as i've replaced the wax motor before). However, I'm not sure where the water solenoid is and what it looks like. Any advice (or pics?) thanks!
User Profile View All Posts by User View Thanks

Gene		#25 Posted : Wednesday, April 11, 2012 3:43:22 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		What is the complete model number of the unit? Gene.
User Profile View All Posts by User View Thanks

supercliff		#26 Posted : Wednesday, April 11, 2012 4:51:39 PM(UTC)
Rank: Member Groups: Registered Joined: 4/9/2012(UTC) Posts: 9		I'm not sure on the model (its at a rental property). I know it's over 10 years old. Would attaching a picture of the unit help? If not can fun the model number on the front of the unit? Where it's currently located I can only see the front of it and it's tough to move....
User Profile View All Posts by User View Thanks

supercliff		#27 Posted : Wednesday, April 11, 2012 4:52:58 PM(UTC)
Rank: Member Groups: Registered Joined: 4/9/2012(UTC) Posts: 9		Also. Any idea on what's up with these odd random posts?
User Profile View All Posts by User View Thanks

Gene		#28 Posted : Wednesday, April 11, 2012 5:28:29 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		The Model Number Locator should help you. Usually the name plate is located on the door frame. Gene.
User Profile View All Posts by User View Thanks

supercliff		#29 Posted : Wednesday, April 11, 2012 7:44:33 PM(UTC)
Rank: Member Groups: Registered Joined: 4/9/2012(UTC) Posts: 9		It is a Maytag model number MHW2000AWW. Thanks.
User Profile View All Posts by User View Thanks

Gene		#30 Posted : Thursday, April 12, 2012 11:04:36 AM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Unfortunately you can access the water inlet valve from the back of the washer only. That means you have to pull the unit out of the wall. Here are the breakdown diagrams and Replacement parts for Maytag MHW2000AWW STACKED WASHER | AppliancePartsPros.com Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (6)

5 Pages<12345> Go to Page...