Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error

2 Pages12>
Options
Go to last post Go to first unread
christophermurphy  
#1 Posted : Monday, February 27, 2012 6:07:39 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

replaced control board and control panel recently to fix dishwasher. worked for a couple of days and now it won't start. the start button did not feel right and so I replaced the control panel again. It still won't start and the start button on the 2nd new control panel does not feel right either. Is it possible to check control panel switches with a digital meter? Is an electrical schematic available for this model?
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
Simon / APP Team  
#2 Posted : Monday, February 27, 2012 7:02:34 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556

Hi, Christopher.
Before replacing control panel check the thermal fuse clipped on the side of the control board. If it is open, replace it.

The fuse Part number: AP3178588
Part number: AP3178588

The test manual should be behind the toe panel.

Post the results.
christophermurphy  
#3 Posted : Tuesday, February 28, 2012 5:45:06 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

The fuse is good. Can't refer to the test manual, as it has been removed from toe panel. The door switch and float switch are good. The resistance of the water solenoid coil is 1000 ohms. There is no voltage at the water solenoid. Pressing the cancel button does turn on the motor to drain the dishwasher and the other buttons light up when pressed, but the start button is non-responsive. The start buttons on both new control panels do not make clicking sound or have any give to them.
Simon / APP Team  
#4 Posted : Wednesday, February 29, 2012 12:52:07 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556

Hi.

Remove the control panel and latch the door. Check if the door switch properly engaging, check for 120v going through it.

Post the result.
christophermurphy  
#5 Posted : Wednesday, February 29, 2012 5:21:54 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

Sorry, if it wasn't clear in my last post, but I've already checked the door switch and the float switch and there is 120volts to ground on both sides of the switches.
christophermurphy  
#6 Posted : Wednesday, February 29, 2012 6:00:58 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

I'm sorry, I made an inaccurate statement in my last post. The door switch has 120 volts to ground on both sides of the switch. After pressing the start button, the float switch does not have 120 volts to it. The float switch does have continuity when checked with an ohm meter.
Simon / APP Team  
#7 Posted : Wednesday, February 29, 2012 7:26:15 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556

Hi,Christopher.
If there is 120v going through the door switch with the door latched, you should check the wires from the control board to the water valve and to the motor for continuity. If the wires checks out OK- replace the control board. To my understanding the control board is still under warranty.

Post the result.
christophermurphy  
#8 Posted : Monday, March 5, 2012 4:01:06 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

I did find the test manual and checked the fill, wash/rinse, and water heating circuits. Everything checks good except the heating element. I will order a control board and a heating element. I will post the results after I install them.

Chris
Simon / APP Team  
#9 Posted : Monday, March 5, 2012 8:32:24 PM(UTC)
Simon / APP Team

Rank: Advanced Member

Groups: APP Team
Joined: 2/12/2012(UTC)
Posts: 5,556

Good luck.
christophermurphy  
#10 Posted : Monday, March 19, 2012 5:20:02 PM(UTC)
christophermurphy

Rank: Member

Groups: Registered
Joined: 2/27/2012(UTC)
Posts: 6

I installed the heating element and the control board and the dishwasher is working perfectly.

Thank you for your help
Christopher
Users browsing this topic
Guest (3)
Similar Topics
KitchenAid dishwasher won't start (Dishwasher Repair)
by bireland 2/19/2012 6:48:35 AM(UTC)
kitchenaid dishwasher won't start (Dishwasher Repair)
by benjo1975 10/10/2010 3:17:42 AM(UTC)
2 Pages12>
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.