5 Pages123>» Go to Page...

Need help troubleshooting Kitchenaid continuously running banging Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: KUCS03FTSS0	Brand: Kitchen Aid	Age: 1 - 5 years
Previous Topic Next Topic

frank the tank		#1 Posted : Monday, November 14, 2011 9:34:26 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		After replacing the directional switch I still have the same problem. Sometimes when I close the door the cycle starts automatically. Then when it gets to the top, it keeps going. Is this another switch iossue? Or Drive gear issue?
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

magician59		#2 Posted : Monday, November 14, 2011 11:11:42 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 8/16/2007(UTC) Posts: 3,273		It sounds like the start switch may be the culprit.
User Profile View All Posts by User View Thanks

frank the tank		#3 Posted : Monday, November 14, 2011 11:41:40 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		Originally Posted by: magician59 It sounds like the start switch may be the culprit. What about the possiblility of the gear assembly?
User Profile View All Posts by User View Thanks

magician59		#4 Posted : Monday, November 14, 2011 1:00:04 PM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 8/16/2007(UTC) Posts: 3,273		After rereading your original post, I reconsidered my response. If it has been goiing on for a length of time, it coudn't hurt to inspect the gears and drive cams for damage. The problem is more likely caused by the upper limit switch (or stop switch). It mey be loose, misaligned, or broken. Part number: AP4701307
User Profile View All Posts by User View Thanks

frank the tank		#5 Posted : Monday, December 5, 2011 4:43:14 PM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		Originally Posted by: airamb It maybe a culprit. Well Ive changed the upper limit/directional switch and the start switch but didnt bother with the new foot pedal looking thing to actuate it. WHAT ELSE?????????? Ugghhh.. Getting frustrated. Any help is greatly appreciated.. I also checked the rods and they seemed ok.
User Profile View All Posts by User View Thanks

frank the tank		#6 Posted : Tuesday, December 13, 2011 7:58:27 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		Originally Posted by: frank the tank Well Ive changed the upper limit/directional switch and the start switch but didnt bother with the new foot pedal looking thing to actuate it. WHAT ELSE?????????? Ugghhh.. Getting frustrated. Any help is greatly appreciated.. I also checked the rods and they seemed ok. I went as far as to replace the centrifugal switch.... Now its worse. Starts EVERYTIME I shut the drawer. I checked continuity on the start switch and it seems ok. Unless I did it wrong.
User Profile View All Posts by User View Thanks

frank the tank		#7 Posted : Tuesday, December 13, 2011 9:13:09 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		Originally Posted by: frank the tank I went as far as to replace the centrifugal switch.... Now its worse. Starts EVERYTIME I shut the drawer. I checked continuity on the start switch and it seems ok. Unless I did it wrong. OK just got done checking everything. The only thing not coming out right is the Y wires from the upper limit and start when connecting to the black wire off the centrifugal switch. I get no reading yet the diagram says there should be a 3-5 ohms reading. So what does that tell me???????????
User Profile View All Posts by User View Thanks

magician59		#8 Posted : Tuesday, December 13, 2011 9:32:44 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 8/16/2007(UTC) Posts: 3,273		Since we already know your motor runs, it probably means there is a disconnected wire somewhere. (or you're taking your reading through an open switch). Were you able to download the manual for your machine?
User Profile View All Posts by User View Thanks

frank the tank		#9 Posted : Tuesday, December 13, 2011 9:51:54 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		yes I have it right here. I have checked all the switches and wires. The yellow is the only ones not closed whereas the diagram shows there should be at least a reading. A yellow goes from solid pack button to the upper limit. The upper limit has a wire going from it to the temporary start switch. From there it goes to the centrifugl switch.
User Profile View All Posts by User View Thanks

frank the tank		#10 Posted : Tuesday, December 13, 2011 9:56:03 AM(UTC)
Rank: Member Groups: Registered Joined: 11/14/2011(UTC) Posts: 27		Ok Im second guessing myself here. I think I may have tested both yellows while they were disconnected simultaneously. Does that make a difference?
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (8)

5 Pages123>» Go to Page...