Customer Support 7 days a week

Welcome Guest! You can not login or register.

Notification

Icon
Error
f3 code on maytag mer5730
Options
Go to last post Go to first unread
Model: MER5730AAA Brand: Maytag Age: More than 10 years
Previous Topic Next Topic
fastfreddy  
#1 Posted : Tuesday, July 12, 2011 11:21:58 AM(UTC)
fastfreddy

Rank: Member

Groups: Registered
Joined: 7/12/2011(UTC)
Posts: 4
When I hit bake and hit the up arrow to 350, the preheat light comes on for a short time and beeps. The light goes off and beeping continues showing f3 fault. What part do I need, and can I replace it?
Back to top
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com 		 
Back to top  
denman  
#2 Posted : Wednesday, July 13, 2011 1:09:09 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Replacement parts for MAYTAG MER5730AAA RANGE- S/C F/S ELE | AppliancePartsPros.com

Here is a manual which covers theses units.
16010161 Maytag Gas and Electric Range Service Manual - ApplianceDigest.com
You have to join the site to download the manual but it is free and this is a very good site for manuals and other info for the appliance repair DIYer.

Looks like F3 is a sensor error so I would start by checking it.
Here is a good link, check out 7,8, 20 and 21.
http://www.applianceaid.com/elecrange.html

If the sensor and it's wiring and the connection at the control board check out OK, then the control board itself becomes the prime suspect.
THIS FORUM IS DEAD!!!!!!!
Back to top
fastfreddy  
#3 Posted : Wednesday, July 13, 2011 12:16:03 PM(UTC)
fastfreddy

Rank: Member

Groups: Registered
Joined: 7/12/2011(UTC)
Posts: 4
Thanks Denman,
Trying to troubleshoot and cannot find the ribbon. I have had the entire console apart. May be looking for a new range.
Back to top
denman  
#4 Posted : Thursday, July 14, 2011 2:50:15 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="DarkRed"]Trying to troubleshoot and cannot find the ribbon[/COLOR]
Sorry but I do not know what you mean by "ribbon"
THIS FORUM IS DEAD!!!!!!!
Back to top
fastfreddy  
#5 Posted : Thursday, July 14, 2011 10:36:48 AM(UTC)
fastfreddy

Rank: Member

Groups: Registered
Joined: 7/12/2011(UTC)
Posts: 4
Troubleshooting instructions say to remove the key pad ribbon from the main board and plug the range back in to see if you still get the error code. If it returns, and the sensor checks out, it is the main board. My sensor read close to 1300 on the ohm meter.

Thanks,
Fastfreddy
Back to top
denman  
#6 Posted : Thursday, July 14, 2011 6:14:35 PM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I looked again at your parts and your control does not have a separate keyboard so there is no ribbon cable.
I think your unit uses an RS1 control Page 1-14.

Your temp sensor seems a little high but should still run through your oven temperatures would be low as the unit thinks it is at about 200 degrees when in fact it is at room temperature.

Did you check the resistance with it unplugged from the board. This ensures that you read only the sensor resistance and not an alternative/parallel circuit on the board.
THIS FORUM IS DEAD!!!!!!!
Back to top
fastfreddy  
#7 Posted : Friday, July 15, 2011 5:39:09 AM(UTC)
fastfreddy

Rank: Member

Groups: Registered
Joined: 7/12/2011(UTC)
Posts: 4
I unplugged the sensor and removed it from the oven to check it. I did this twice and the first time was a little higher.
This all happened after doing a self clean.
Where do I find the RS1 control Page 1-14 on the internet?
Thanks
Back to top
denman  
#8 Posted : Tuesday, July 19, 2011 1:15:34 AM(UTC)
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Sorry for not getting back to you sooner but have been at the cottage.

I was refefring to the manual that I included in the earlier post.
THIS FORUM IS DEAD!!!!!!!
Back to top
Users browsing this topic
Guest (5)
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Privacy Policy | Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET