Rank: Member
Groups: Registered
Joined: 8/27/2008(UTC) Posts: 14
|
The Microwave works perfectly except it does not heat anything. All the buttons and lights are working, the turntable spins and the light comes on inside. Any suggestions? Thanks.
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Views messages in topic : 27,455
Was thanked: 4 time(s) in 4 post(s)
|
In order to provide most accurate advise we need the complete model number of the unit. You can find it on the oven door frame.
Gene.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/27/2008(UTC) Posts: 14
|
I found the following: 8538 793 54001 XNF 1310108
One other thing, I powered off at the circuit breaker and back on and a red code PF showed up on the left of the display. I figured that might mean Power Failure but I don't know.
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Views messages in topic : 27,455
Was thanked: 4 time(s) in 4 post(s)
|
"PF" means power failure. Just push the Cancel button to get rid of it.
The model number is on the right side of the Oven door frame.
Gene.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/27/2008(UTC) Posts: 14
|
Got it! Thanks.
RMC305PDQ1
June '96 is the date of manufacture as well. Older than I thought but since its a built in two part system I'd like to fix it rather than replace it.
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Views messages in topic : 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Open the control panel and check the 20 Amps fuse behind the control panel. Replace if it's open. - The part number for the fuse is AP3010073 Here are the break down diagrams for the Whirlpool oven/microwave combo Model RMC305PDQ1Gene.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/27/2008(UTC) Posts: 14
|
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Views messages in topic : 27,455
Was thanked: 4 time(s) in 4 post(s)
|
You're welcome. Keep us posted.
Gene.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 8/27/2008(UTC) Posts: 14
|
..any tips to removing the control panel? Other than turning power off!
|
|
|
|
Rank: Advanced Member
Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Views messages in topic : 27,455
Was thanked: 4 time(s) in 4 post(s)
|
Open the oven door. Remove the screw on each side of the trim. Pull the trim toward yourself from the bottom and slide it down to release it from the control panel tab.
Remove the screw on each side of the control panel bottom tab. Pull the control panel bottom toward yourself and lift it up to release from the top tabs. Now it's all yours.
Gene.
|
|
|
|
Forum Jump
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.
Important Information:
The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close