2 Pages12> Go to Page...

Washer Won't Drain Spin Or Agitate Options  Email this topic  Watch this topic  Print this topic » Normal Threaded
Model: LSE7806ACE	Brand: Maytag	Age: 5 - 10 years
Previous Topic Next Topic

carlous		#1 Posted : Thursday, July 17, 2008 6:40:14 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 11		Washer will fill but will not agitate spin rinse or drain. I have replaced the timer.
User Profile View All Posts by User View Thanks

Sponsor
	See inside of your appliance - diagrams and part photos for virtually every model. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com

Oscar		#2 Posted : Thursday, July 17, 2008 6:51:35 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 4		Does the timer advance? If not check your lid switch.
User Profile View All Posts by User View Thanks

carlous		#3 Posted : Thursday, July 17, 2008 11:05:17 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 11		Do I have to purchase the switch assembly w/fuse? Would that be easier to replace than the switch itself?
User Profile View All Posts by User View Thanks

Oscar		#4 Posted : Thursday, July 17, 2008 12:22:09 PM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 4		Lid switch does not have a fuse. Switch allows 120v to go back to motor and operate. The lid switch is a saftey device to prevent people from putting their hands into the machine when it is running. To verify switch is bad, unplug from wall, unplug lid switch and place ohm meter leads across lid switch. Activate lid switch and verify reading goes to zero, if not replace switch.
User Profile View All Posts by User View Thanks

carlous		#5 Posted : Wednesday, July 23, 2008 4:30:36 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 11		I replace the lid switch. I still don't have anything. What else might it be?
User Profile View All Posts by User View Thanks

Gene		#6 Posted : Wednesday, July 23, 2008 6:41:32 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		Does the motor run? Did you check the belts? Gene.
User Profile View All Posts by User View Thanks

carlous		#7 Posted : Thursday, July 24, 2008 5:20:57 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 11		The motor isn't running. The belts look okay.
User Profile View All Posts by User View Thanks

Gene		#8 Posted : Thursday, July 24, 2008 7:13:02 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		When you said you replaced the lid switch - did you replace the whole assembly including the fuse? Check this fuse and if there is nothing wrong then, most likely, the problem is a bad water level switch (#6 on the break down diagram). Gene.
User Profile View All Posts by User View Thanks

carlous		#9 Posted : Monday, July 28, 2008 8:29:05 AM(UTC)
Rank: Member Groups: Registered Joined: 7/17/2008(UTC) Posts: 11		I replace all switches and now something keeps blowing the fuse located at the front oof the machine
User Profile View All Posts by User View Thanks

Gene		#10 Posted : Wednesday, July 30, 2008 4:29:04 PM(UTC)
Rank: Advanced Member Groups: Senior Expert, Administrators Joined: 7/19/2007(UTC) Posts: 27,455 Was thanked: 4 time(s) in 4 post(s)		These two switches on the lid switch assembly should be properly adjusted so when one of them is "open" the other one is "closed". Gene.
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (4)

2 Pages12> Go to Page...