Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Post a reply
From:
Message:

Maximum number of characters in each post is: 32767
Bold Italic Underline   Highlight Quote Choose Language for Syntax Highlighting Insert Image Create Link   Unordered List Ordered List   Left Justify Center Justify Right Justify   Outdent Indent   More BBCode Tags
Font Color Font Size
Security Image:
Enter The Letters From The Security Image:
  Preview Post Cancel

Last 10 Posts (In reverse order)
Wayne Addison Posted: Tuesday, December 6, 2011 4:36:40 PM(UTC)
 
We ran a test:

Turned the unit on and ran a normal wash.
Halfway thru the wash/rinse cycle we opened the door slightly.
Steam can out and it was obvious that it was washing properly.
We opened the door once again at the end of the wash rinse cycle and onece again steam came out.
The dishes were warm but not hot.
Still wet at the end of the "dry" cycle.
Could it be that the heater is not getting hot enough?

Thanks for your input.
ApplianceJunk Posted: Monday, December 5, 2011 12:13:52 PM(UTC)
 
Yes it does.
Wayne Addison Posted: Monday, December 5, 2011 11:48:17 AM(UTC)
 
My main question is:
Does this model Kitchenaid come with a dry cycle in it's normal operation?
Thank you for your assistance.
ApplianceJunk Posted: Monday, December 5, 2011 11:04:50 AM(UTC)
 
Here is a copy of the tech sheet for your model dishwasher.
It includes a troubleshooting guide that may help you better diagnose the problem.
ApplianceJunk Posted: Monday, December 5, 2011 10:59:16 AM(UTC)
 
Quote:
I did ask the tech about the Energy Saving Dry and he replied basically the same as you did, ie; drip dry.


Yes, drip dry if it's selected and if it's not selected it should use the heater to dry them.

Quote:
Do you think I need to replace the heating element and add a board with that option?


Your heating element could be bad, but from my experience I doubt it.
To check the heating element I would simple disconnect the power to the dishwasher, remove the wires from the heating element and check it with my ohm meter.

I believe the control board that is in your dishwasher now already has the option you are looking for, it's just not working.
Wayne Addison Posted: Monday, December 5, 2011 10:46:30 AM(UTC)
 
I did ask the tech about the Energy Saving Dry and he replied basically the same as you did, ie; drip dry.

Do you think I need to replace the heating element and add a board with that option?

Thank you,

Wayne
ApplianceJunk Posted: Saturday, December 3, 2011 11:36:02 AM(UTC)
 
I would think with 'energy save dry' selected the dishes would drip dry and without it selected it would use the heater to dry them.

For the fun of you you should ask the technician that looked at it and see what he says about the 'energy save dry' option. :)
Wayne Addison Posted: Saturday, December 3, 2011 11:28:50 AM(UTC)
 
The control panel read:

Baked on cookware
Normal
Light/china
Quick clean up
rinse only
high temp scrub
sani rinse
energy save dry
4 hour delay

hope this helps

Wayne
ApplianceJunk Posted: Saturday, December 3, 2011 6:39:58 AM(UTC)
 
What option do your buttons give you on the front of your dishwasher now?
ApplianceJunk Posted: Saturday, December 3, 2011 6:38:53 AM(UTC)
 
Did it use to dry the dishes?

If (and it's a big if) what the technicians said was correct I would think that the control board and control panel would need to be replace from a model that had the dry cycle.