Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

10 Pages<1234>»
Options
Go to last post Go to first unread
VBN  
#11 Posted : Tuesday, November 20, 2007 2:07:55 PM(UTC)
VBN

Rank: Member

Groups: Registered
Joined: 8/17/2007(UTC)
Posts: 5

In your opinion- Can I just change the 2 surface ignitors for the stove to work.
I can live without the oven/broiler for now. How difficult is it to change these ignitors? Do I have to change the spark Module too?
Thank you
Gene  
#12 Posted : Tuesday, November 20, 2007 2:35:43 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert
Joined: 7/19/2007(UTC)
Posts: 27,455

The stove and the oven are operates absolutely separate. In order to fix just the stove you have to replace the igniters and the spark module.

The job is not very complicated. Just be careful and do not forget to remove the power from the range first.

Gene.
geeo  
#13 Posted : Tuesday, November 27, 2007 11:56:27 AM(UTC)
geeo

Rank: Member

Groups: Registered
Joined: 11/27/2007(UTC)
Posts: 1

Same problem, my fix involved swapping the broiler ignitor with the oven unit to get it up and running. The only issue was with the wire lengths.
Now I'm ready to order the round ignitor but the photo does not show the mounting tab located at the rear with 2 holes approx 1/2" apart.
The mounting looks similar to the flat model.
Any ideas???

Thanks
geeo
Gene  
#14 Posted : Tuesday, November 27, 2007 12:14:51 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert
Joined: 7/19/2007(UTC)
Posts: 27,455

The mounting bracket is not shown clear on the picture but it is a standard for all kind of the round igniters and it will match up with your old one.

Gene.
btoups  
#15 Posted : Friday, January 25, 2008 7:56:06 PM(UTC)
btoups

Rank: Member

Groups: Registered
Joined: 1/25/2008(UTC)
Posts: 2

I have a frigidaire natural gas range model PLGF389CCA with an oven that has been slow to heat up. After reading these posts, I have concluded it is probably the igniter. I took the oven floor up and removed the flame spreader and turned the oven on, but the igniter did heat a very little, but it did not get red hot or anywhere near that after 20 seconds, so I turned the oven control back off. I conclude that the igniter is most likely the problem, and since I don't have an amp meter I can't check the current draw.

I have taken the igniter off its mounting by unscrewing the two screws holding it in place. I cannot see how the wires are connected to their supply since they are only about 2 inches long and appear to go into the back of the oven. I have seen posts here that say to cut the wires and attach the new igniter using ceramic wire nuts, which will be somewhat difficult given how short the existing wires appear to be. If it is simple to do, I would prefer to attach them at their source, but I don't know how to access that. Any words of wisdom /voice of experience are appreciated.

Thanks for the help,
Brad
Gene  
#16 Posted : Saturday, January 26, 2008 6:25:53 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert
Joined: 7/19/2007(UTC)
Posts: 27,455

Hi Brad,

Pull the range out, remove the back cover and you will access the igniter connection.

- The part number for the oven igniter is AP2150412

Gene.
btoups  
#17 Posted : Saturday, January 26, 2008 10:48:24 PM(UTC)
btoups

Rank: Member

Groups: Registered
Joined: 1/25/2008(UTC)
Posts: 2

Thanks for your help!
Brad
2835AW  
#18 Posted : Monday, March 24, 2008 7:57:03 PM(UTC)
2835AW

Rank: Member

Groups: Registered
Joined: 3/24/2008(UTC)
Posts: 3

G.e. Oven Replaced Ignitor Oven Still Will Not Light
Gene  
#19 Posted : Monday, March 24, 2008 8:50:52 PM(UTC)
Gene

Rank: Advanced Member

Groups: Senior Expert
Joined: 7/19/2007(UTC)
Posts: 27,455

What was the original problem?

What is the complete model number of the unit?

Did you perform a troubleshooting prior to replacing the part?

Gene.
2835AW  
#20 Posted : Wednesday, March 26, 2008 6:13:29 PM(UTC)
2835AW

Rank: Member

Groups: Registered
Joined: 3/24/2008(UTC)
Posts: 3

Original Problem Over Or Broiler Will Not Light
Model#jgbc20gev3wh
No Prior Troubleshooting
Users browsing this topic
10 Pages<1234>»
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.