Part Equivalent to C8931505 - Appliance Repair Forum - Free Service from Appliance Parts Pros

Welcome Guest! You can not login or register.

Notification

Error

Part Equivalent to C8931505 Options Email this topic Watch this topic Print this topic » Normal Threaded
Model: SZD25NL	Brand: Amana	Age: More than 10 years
Previous Topic Next Topic

JMJNet		#1 Posted : Tuesday, May 6, 2014 10:29:30 AM(UTC)
Rank: Member Groups: Registered Joined: 7/7/2008(UTC) Posts: 21		I noticed when I search for relay no. C8931505, it shows No Longer Available. I was reading some of the Q&A with some conflicting part no. I wonder what is the equivalent part replacement for this part. If there is a complete kit that includes the relay, overload and capacitor? Thanks.


User Profile View All Posts by User View Thanks

Sponsor

See inside of your appliance - diagrams and part photos for virtually every model.

richappy		#2 Posted : Wednesday, May 7, 2014 3:32:59 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		What is your problem, compressor no run, etc


User Profile View All Posts by User View Thanks

JMJNet		#3 Posted : Wednesday, May 7, 2014 5:31:11 AM(UTC)
Rank: Member Groups: Registered Joined: 7/7/2008(UTC) Posts: 21		After some diagnosis, I determined that the ptc relay is bad.


User Profile View All Posts by User View Thanks

richappy		#4 Posted : Wednesday, May 7, 2014 7:59:17 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		If you have a meter, I can help, but I hope you made a diagram where each wire goes.


User Profile View All Posts by User View Thanks

JMJNet		#5 Posted : Saturday, May 17, 2014 5:27:53 PM(UTC)
Rank: Member Groups: Registered Joined: 7/7/2008(UTC) Posts: 21		Sure, I have a DVM. Thanks for the help.


User Profile View All Posts by User View Thanks

richappy		#6 Posted : Sunday, May 18, 2014 1:50:40 AM(UTC)
Rank: Advanced Member Groups: Senior Expert Joined: 9/10/2007(UTC) Posts: 9,586 Was thanked: 2 time(s) in 2 post(s)		Hold the old ptc device with the input, male, spade terminals facing you and the tab on top, pins on top. If you measure a short from the top, right terminal to the output, round compressor terminal on the other side,right and an open, or 5- 10 ohms from the same input terminal, to output, round compressor terminal on the left, you have the standard ptc device, the start terminal is on the bottom,left. If you measured 5 - 10 ohms, your ptc device is ok. If so, you can use a WR07X10051 ptc One fridg power wire goes to the overload, the other to the right input spade terminal of the ptc. If not, your start terminal is bottom, right, or if the common compressor terminal is on the bottom, then start pin is upper left.


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest (2)

Forum Jump

You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close